Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi,
I am beginner with NRF52840. I want to create a task scheduler using multiple tasks with different level of priorities that is low, medium and high. I am using SDK...
Hello,
I got two PCA10056 1.0.0 DKs equipped with an nRF52840 rev. 1 (code AC0). Both do not measure the VCCH voltage correctly (displayed voltage ~2.4V instead of 3.0V...
This forum feels pretty advanced, so if this is the wrong place to ask this question apologies and please let me know where I should be asking it instead.
My goal is to...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0, with updated MDK (see link )
IAR EW ARM...
Hi Everybody,
I need help in writing a little software on NRF52805 which will active the transmitter with parameters:
1) Frequency : 2402Mhz only. (and i will later...
Hi,
I'm using nRF52832 with S140 v7.2.0 base on nRF5_SDK_17.1.0. I use PCA10100 development kit and set VDDH/5 as input and use internal reference (0.6 V) to do the battery...
Hi
I am working on SPI implementation on BL653_dvk board and while SPI_transfer i want to capture the timeout error.
but not able to differentiate which timeout is correct...
Hello,
We are using MDBT42Q-512KV2 module which is based on nrf52832. There is Central and peripheral ( Foot Pedal Switch ) using same module.
We have used crystal from...
I know from the product specification for the nRF52832 chip that the high frequency clk can use a external 32 MHz crystal as source. My question is, is it possible to supply...
Hello!
I am now developing a product with NFC based on nrf52833.
I need to transmit some crucial data between device and phone, such as device settings.
But I have...
Hi all,
I would like to measure time intervals between gpio edges along with Matter.
I tried to use a 100us timer interrupt but seems it will crash the original matter...
Dear Support
I have made the following findings of my evaluation of the NRF5340 with Version 2.1.0 SDK:
-CIS mode has no constant delay at default settings 48-4. According...
Hello Nordic team,
I have looked at the BLE + Zigbee multiprotocol examples from nRF5 SDK and in these examples, I see that there is a file ' multiprotocol_802154_config...
Hello,
are NRF SoCs considered as BLE certified?
What is the default firmware in such case?
I guess no fw changes are allowed so that certification remains valid, right...
If I only wanted to allow one bond at a time, how could I do this?
For example when someone connects for the first time they would pair and bond, by entering the passkey...
