We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I want to implement OTA (Over-the-Air) updates using Thread on the nRF52840 DK board.
Are there any sample codes or references available for achieving this with Thread?
Hello,
I'm trying to use nRF9160 Development kit and it is not showing up in connected devices view in VS code.
Switch position is correct(nRF91) on the development...
I am using v3.0.2 SDK, nrf52832 DK, and I am learning academy.nordicsemi.com/.../ . I encountered a problem in step 4.2:
Please help me find out how to debug
With the NRF_CLOUD_MULTI_SERVICE sample, we'd like to set the GNSS location tracking sample interval to 2s or even 1s.
But we found that the actual time will be about 25s...
Hello everyone, I need to attach a QSPI memory to an NRF54L15 module. I am led to believe that this should be supported out of the box but cannot understand how to use the...
Hello everyone,
I am working on a project where I need maximum range and TX power, since my Bluetooth device will be implanted the signal is strongly attenuated I need maximum...
Hi,
We are evaluating the NRF9151 for live tracking purposes. While testing with the nRF9151-DK we noticed the we had tracking fallouts using AT#XGPS=1,1,1 both during driving...
Hi everyone,
After the latest update of the nRF Connect SDK plugin for VS Code (2025.4.106), we've seen this pop-up appear. We are using v1.8.0 and now we are not able to...
Assume the nRF21540 used as a front end for nRF52840. When the nRF21540 module is in power down mode can it pass the signal without significant loss? If yes what is insertion...
Hello,
I've searched a good amount of online content, but I cannot publicly find a good enough reference design for the nrf52840-DK, natively compatible with Kicad.
...
Now I can use LIBUARTE to receive data from MCU, but have a trouble: it can't receive a whole packet sometime,and return it with 2 parts.
UARTE : 115200/8/1
receive buffer...
Hi Support Team
I installed the NCS V3.1.0 just now. But there was an issue of west: unknown command "build" for the NCS V3.1.0 when I built a sample. Many thanks.
Hi,
I'd like to raise this issue I am having with the v3.0.1 sdk wherein the final build stages I get the message attached
I am using the Lesson 9 exercise 5 sample...
I am trying both v3.0.0 and v3.0.2 SDK; the board I am using is the nRF9160DK, version 1.1.0. There are 4 scenarios:
1) Run on Linux (minicom or Serial Terminal) following...
