I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi there,
So in my previous posts, I have been asking questions about setting i2s on two nRF devices in different modes. I have been successful in making it work.
...
Hello,
is it possible to read UICR at address FF8000 from a non secure application for nrf(160.
If yes, can you provide sample code and CONFIG to enable in prj.conf. ...
Hi,
I’m currently working with the nRF9151DK and using the nrf_modem_lib to test some AT commands. However, I’ve encountered an issue with the SIM.
When executing the...
When using the SPIM4 at 8 or 16 MHz, the clock looks nice and even. But at 32 MHz it consistently skips a half beat on the 16th clock pulse. In other words, while all the...
I am working on nRF54L15 and I want to store some user data in flash and for that I want to define the partitions.
I have selected the Target: nrf54l15dk/nrf54l15/cpuapp...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
Body:
Hello Nordic Team and Community,
I am working on a project using an nRF52840 chip on a custom breakout board . I am not using any pre-made development boards or...
During the testing phase of my device I use the Zephyr (uart) logging module and the Zephyr shell module(CONFIG_SHELL_LOG_BACKEND=y). Shell is mostly disabled, and is enabled...
I followed the migration guide for NCS 2.8.0 here for a custom board with engineering rev B silicon. After doing so I can't flash the board anymore and it gives me this error...
I am developing my product using the desktop app in the NCS SDK. I found that during OTA, it can only upgrade from a lower version to a higher version. This means that when...
I am using Keil v5 and the nRF5 SDK 17.1.0 .
I use this example.(nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10040)
I hope the chip enter system off...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The board's USB pin connections are designed based on the nRF9160-DK's nRF52840 reference...
Hi,
I just received my Thingy91x. I followed the onboarding and created a provisioning profile in NRF Cloud. The device did not connect and no logs appeared in Serial terminal...
