Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
NCS 2.4.1 nRF52840
My project is a battery powered SED based on the coap_client example. It is configured to autojoin using a hard coded pksd. I see on Wireshark that my...
Hello, I want to configure the BMP390 using I2C on my custom board. However, when I try to read the CHIP_ID register, I am unable to get the default value, and the function...
Hi,
I referred to this doc for hardware setup
However, in the programmer in nRF Desktop, I got the following log:
17:37:36.199
Error: Failed with exit code 1...
Hello person in charging,
I would like to know whether there are something information on vulnerabilities in the proprietary mode of nRF51 and nRF52, respectively.
Thanks...
Hello,
After an update to the NRF connect for Desktop the Programmer application can no longer program my nRF52840 dev kit (PCA10056, 3.0.0). Trying to revert the update...
Hi,
In our project, we're using Mcumgr FS to download files from our device.
After tweaking the BLE configuration parameters using the throughput sample ( https://github...
Hi
The datasheet of the nRF9151 is missing the statement in the nRF9161 datasheet:
RF 3GPP compliancy requires 3.3 V.
Is the nRF9151 reaching compatibility down to 3V...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Recently, we started developing our new project using the nRF52832 as our controller.
We are using Segger Embedded Studio (5.42a) as our IDE.
My question is: Are there...
I work for nRF52833 on NCS2.8.0.
I try to set SB_CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT=y for sysbuild.
build error is occured.
Maybe there is not enough RAM for mcuboot...
My NCS version is 2.6.1, and the modem firmware version is 1.3.6
I found that delta upgrade often fails when testing the firmware of FOTA upgrade modem for 9160. Currently...
Hello. How can I monitor that SoftDevice is working properly? I am trying to monitor using Radio notification, but RADIO Active does not guarantee that the SoftDevice is working...
Hi ,
I am running "Cellular IoT Fundamentals". In Lesson 4, Exercise 1, has MQTT communication. Everything went well up to the point where I have to PUBLISH from MQTT Explorer...
