I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi, I'm using v4.0.4 of the standalone Bluetooth Low Energy desktop application to obtain and display GATT details of a connected device. I enable indications on the Service...
One of our employees is following the Cellular Fundamentals courses and they got stuck on getting modem traces out of the Thingy:91X.
In lesson 7 exercise 1, the course...
I have been trying to understand Child Supervision. Part of the documentation that I have read is:
https://openthread.io/guides/build/features/child-supervision
At the...
Hello!
I'm working on a project that was primarily developed with NCS v2.9.0. The application (using an nRF5340) utilizes BLE mesh and is configured to use TinyCrypt for...
Hello,
I am using nRF52833 with nrf connect sdk for vs code (SDK and Toolchain version : 2.9.1).
Hello Nordic Team,
I am using OTA DFU with MCUboot on the nRF Connect...
I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
I am trying to flash and use the debugger on a nrf52840 DK to flash a Thingy53, using the ribbon connector as outlined in this video . I tried to follow the steps in this...
nRF9160, SICA B1A, mfw 1.3.7, NCS 3.1.0
I currently try to test the situation, when the battery gets drained "too much" and the voltage drops below 3.0V (e.g. 2.9V) on VDD1...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
My project is running on an nRF52832 with the soft device enabled. At the start of my project I have the following
When I reset the system our normal way (calling nrf_pwr_mgmt_shutdown...
Dear all,
I wanted to modify BTHome template sample for Home Assistant software in order to run enable it to advertise on PHY Coded, there I guess I need to enable extended...
Hello,
The following code performs an I2C write-restart-read operation that works correctly on a NRF52840 devkit with ncs v3.1.1, but fails with ncs v3.2.0 and v3.2.1. Note...
If I source the toolchain environment (using eval "$(nrfutil sdk-manager toolchain env --ncs-version v3.2.1 --as-script sh)" ), the curl CLI stops working:
The toolchain...
Hi everyone,
I’ve just started my adventure with the nRF52xxx family and have already hit a wall. In my previous project, I successfully programmed an nRF52840 dongle, but...
