I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
1. I tried flashing all ble codes to my nrf kit. It does not seem to connect on Windows machine but connects on Mac. My other nrf kit connects perfectly fine. What is...
Hi,
I was wondering what I need to do, or if it is even possible, to debug a non-secure app which uses TFM.
Running 'west debug' on e.g. the blinky sample works regardless...
I’m running a self-built BLE application on the nRF52DK board. It used to work fine before, but recently it has stopped working. The board still runs all the sample codes...
Problem : I am following on Bluetooth Fundamental Course on Nordic Academy webpage. I successfully advertising BLE with non-connectable option. But change adv_param to BT_LE_ADV_OPT_CONN...
Hi there,
I have implemented the ability to pair the BLE peripheral in our app. However, some users may prefer to connect via IOS settings.
I have seen a thread which...
Hi ! Its me again. I'm using zephyr 3.5.0 via zmk. I'm trying to play a 60 Hz uncompressed PCM file from a wav embedded in flash memory.
I'm noticing some inconsistent output...
I had previously existing firmware that performed a firmware upgrade using mcuboot and dfu_target. This was done over bluetooth but did not use any existing available bluetooth...
Hello,
I'm trying to build my program for a custom board with FOTA BLE.
Im using v2.9.0 for the SDK and the toolchain. The custom board has a nrf52832.
When building...
In the 'nRF91 Series Antenna and RF Interface Guidelines' document there is a section ' 4.3.1 Combined GNSS and LTE antenna example' which shows a potential way to use a single...
Hi everyone,
I have an nRF9151 connected to an nRF52840/(or nRF54l15) over a single UART . I want to:
perform DFU of the nRF52840 from the nRF9151, and
also...
I am currently working with the Channel Sounding sample on the nRF54L15 DK boards (SDK and toolchain v3.1.1) and using Nordic’s multiple-antenna support as described here...
Hi,
I have a general question about the GRTC accuracy on nRF54L15.
In the manual it states the following:
We will like to use the GRTC as timekeeper with an external...
HI all,
I'm working on a firmware for the nRF9151. In the development desk all works good. But under release conditions the software crashes cause of locked RAM access...
After using the official example hci_uart with the nRF54L15-DK, it is configured as an HCI controller. I used bluetoothctl commands like scan on and connect to scan for peripheral...
I'm leveraging a fuel_gauge example to pass a version string as part of a Device Information Service. When viewed in Nrf Connect (desktop or mobile) only the first character...
