I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
We are evaluating Segger SystemView for analyzing our embedded applications. However, we encountered occasional overflows in SystemView. These overflows are caused by...
Hello
how can i found a input capture example to read external 125KHz PWM Signal, so we can measure the time from falling/falling edge or rising/rising edge or falling/rising...
Hello, from reading devzone, the recommendation for optimal GPS performance while using the nRF9160 DK, is for the antenna to have an unobstructed view of the open sky.
...
Hello,
We have got some devices in the field that run mfw1.3.1 and an application that have some issues with preforming modem FOTA correctly. I'd like to update them to...
Hello,
I have been trying to provision and configure two nodes running Light and the Light_switch examples using a separate node running the mesh provisioner example from...
Hi,
I'm porting an older product that used a Microchip MRF24J40 SPI radio and a PIC processor to an nRF52840 and I'm struggling with how to replicate both the CRC calculations...
Hello,
I am using nRF Connect for VSCode (v2022.7.242) and discovered that the softreset option for a task has no effect.
Task:
Output:
As you can see it is...
Hi All!
I am using a hologram NB-IoT sim card in nrf9160DK. And want to connect it /send data to nrf cloud. I have activated the sim from the hologram website. When I tried...
I bought this device becouse I want to use it as Open Thread Border Router.
I followed the steps on your website: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All:
Good night!
We have 3 pcs of nrf52840-DK and would like to implement and test remote provision functionality with nrfsdk_17.0.2 and nrfsdk_mesh_5.0.
When compiling...
Hi，i'm use latest ncs sdk to develop bluetooth application which use Periodic advertising, when i get started with samples(bluetooth/periodic_adv), and use Ellisys capture...
Hello,
Is AT+COPS manual selection mandatory or just a preference? We have an issue with 9160 choosing a network without PSM if it has better signal quality (when roaming...
Trying to flash devices and getting this error:
make flash
DONE nrf52840_xxaa Flashing: _build/nrf52840_xxaa.hex nrfjprog -f nrf52 --program _build/nrf52840_xxaa.hex ...
Hi,
In our old project we developed low energy sensors based on the Nrf52811 (nrf Connect sdk), using advertisements to broadcast the sensor data, then collecting them with...
