I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
This is a 2 part question concerning the LFCLK input levels as well as how to test the LFCLK frequency against the HFCLK frequency to make sure they are consistent.
In this...
I am currently working on a project using the MAX30102 Heart rate module. This sensor has red & ir led's. I connected the the max30102 sensor to the nrf52 DK as follows VDD...
Hi,
I'm looking at the BLE aggregator example, it uses a service called "ble_agg_cfg_service" .
1. It looks like this service is the same as NUS ?
2. I'd like to...
Hi
I am evaluating the production of a BLE product and your chip solution looks promising.
In my case the bluetooth will be connected to PC and it should be recognized...
There are a number of issues in ble_advertising that relate to changing the status of advertising in response to events. Specifically the current adv mode is not changed on...
Looking at the schematic diagram of the ISP-1507-AX Test Board….
www.insightsip.com/.../ISP1507_AX_TB_Schematic.pdf
… I can see that there is the possibility to connect...
Hi
I am using ble_app_uart code from ble_peripheral folder and nrf_connect app to receive/send data.
I have interfaced external sensor with UART pins and receiving data...
Hi I am using UART code from nRF5_SDK_16.0.0_98a08e2\examples\peripheral.
I have checked loop back with default UART pins,which are 5,6,7,8.
Now I want to interface some...
Hello,
I am using a nRF52DK (PCA10056). When I connect the board, the J-link drive opens up, but it does not detect on nRF Go Studio, nor is it flashing any code. I am using...
I'm using the USB CDC ACM example to write a message to a com port. I can receive messages fine except there is one problem. I am receiving the characters one character at...
Hi,
Is it possible to use two LPCOMPs simultaneously?
I would like to use analog channel 6 and 5 and if I register a RESULT Above on channel 6 it should start a software...
Good day to all
I would like to get a little more information about the function:
added in softdevice version 7.0.1.
Starting the radio in connection mode is shown...
Hi,
I'm experiencing some UART issues on nRF52832 where it seems like the peripheral is not correctly reset when doing a soft reset. After a soft reset I expect that the...
Hi,
I am using nrf25840 Dongle as NCP with Linux machine. I have used NCP example hex from " nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\thread\ncp\usb_bootloader...
How to achieve the lowest power consumption while "sleeping" but still being able to awake from an internal timer ?
For the timer I'm using the Ticker class from mbed.....
