Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hello. I am using vscode. I added sdcard to broadcast_sink in the existing samples in applications/nrf5340_audio and checked the list with the serial monitor and wanted to...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
Hello, I am using peripheral uart as my base project and uppn that, I have built my application.
I am delibrately changing the flash region just to see if i can modify flash...
Hello, I can commission nrf52840 bulb by iPhone successfully using below QR code:
https://project-chip.github.io/connectedhomeip/qrcode.html?data=MT%3A6FCJ142C00KA0648G00...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
I am trying to make a FOTA to update the firmware of the nrf9151 using the command AT#XFOTA, the issue I am having is that I am unable to have the app_update.bin file generated...
Hello, I am currently working with NRF5340-DK dev kit and I want to use 2 SPI devices connected on the same SPI bus OR use 2 different SPI instances, however none of these...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
I have a similar question as posted here but I wonder if this limitation is still the case.
I am trying to advertise to a specific device by passing the scanner device's...
Hello all,
I´m Trying to Run the Minimal-Example of Sensor-Stream API
https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/sensor/stream_drdy#id7
HW is:...
Hi All,
I have a ordred couple of 5340 Audio DKs. I want to configure one of them as headset using the nrf_audio example application and connect to a phone and stream...
I'm developing code to run on the nRF5340 SoC in a Thingy:91 X and I am seeing duplicate RTT output. For example, if I look at the RTT output from the default 'Connectivity...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
