Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
When advertising using BLE and using the nordic app, it seems that the advertising address changes after every reboot even with CONFIG_BT_PRIVACY set to n. However, this only...
Hi,
we are using nrf52 DK and our custom mobile application. We are trying to collect 15000 sensor samples and finally we are trying to send array to mobile app via BLE...
I suspect there is a bug in the https_client sample. sdk-nrf/samples/net/https_client/src/main.c
The certificate seems to always be provisioned and
mismatch = modem_key_mgmt_cmp...
I have tried to use the power profiler and I got the notification that my firmware had to be updated. I clicked proceed and the device started updating.
When the update...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using NUS to work with...
My Android app builds and runs fine under Android 13.
But on Android 14 when I try to use the DFU library (ver. 2.5.0) I get the following run-time error: One of RECEIVER_EXPORTED...
I have two nrf5340 audio DKs running bidirectional audio over Bluetooth. Software is modified Audio example from SDK 2.7.0. I am trying to run external i2s in the unicast...
Hello,
I am currently programming using SPIM+Timer+PPI(via nRF Connect SDK v.2.6.1), but due to my lack of understanding, handling handlers is challenging. Therefore, I...
Hello! I am using the nRF5340 dev board with an nRF7002ek wifi shield to connect to MQTT using the Zephyr MQTT library and MQTT 3.1.1 (the only supported version by Zephyr...
Dear Nordic Team, I am currently working with 2 Infineon IM73D122V01 PDM Mems microphones to obtain stereo data, One is configured as left and the other is configured as right...
Hi,
We have 2 projects where we are using the nPM1300.
In both cases we have peak currents.
In de documentations I thought I read some where that the current limit was...
Hello,
this is connected to the question:
For our application I need all radio on/off events. The sample "connection event trigger" sample only gives one trigger per connection...
Hi Nordic,
I am implementing a micros() in the arduino using nrfx driver.
Below is test code and I got some questions.
[Question 1]
Timer 1 and Timer 2 works...
