Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I am developing LTE-M software on nRF9160. Previously, I checked that it runs well with nRF9160DK. Now I try it with my own board.
First, only for testing, I made following...
Hi, I'm trying to set up wireless audio stream using 2 nRF52832 Dev Kits and SGTL5000 audio boards. SDK: nRF5 SDK 17.1.0 For the wireless protocol I've used ESB, and the program...
Hi, I've been trying to modify some of the nRF5 SDK 17.1.0 BLE HID examples to make the nRF appear as a BLE HID Braille Display, that would be recognized in Android's TalkBack...
Hello,
I'm modifying the code of Wireless timer synchronization among nRF5 devices blog to use RTC instead of two TIMERs. I started with the code on Git for SDK 16. Writing...
Today I opened VS Code to find all my Zephyr/NRF #includes have the red squiggly lines with an error such as "cannot open source file zephyr/types.h". Right click -> Go to...
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
Hello,
I am trying to interface a TCA9548A Multiplexer on my custom board. I am able to set up the channels and read the channel status' with device_get_binding successfully...
I'm just trying to get my feet under me to write some code for the nina-306 module. I'm playing along, and following the dev academy course. I can't tell if this worked or...
I'm trying to do my first Blinky app with nrf52811. I followed all installation procedures by DevAccademy.
I created a new application by the available sample (blinky led...
Hello,
I am currently using the BLE NUS example from the Nordic Dev Academy course for BLE ( https://github.com/NordicDeveloperAcademy/bt-fund/blob/main/lesson4/blefund_less4_exer3_solution...
Hi all,
I am trying to use MCUBoot on the nRF52840, and am having troubles with this: Whenever my device boots, it always immediately goes to bootload mode and I can't get...
hi all,
ST7735 driver for TFT Display which is tested using example/peripherals/GFX library, we want to test touch screen for this display ,the touch screen driver used...
I am currently working on a project using the nRF52840-DK and the Power Profiler Kit II. I have created an application based on the "NFC System Off" sample. However, I am...
Hi could you provide any insight on the following issue:
Source code in main.c
#include <zephyr/kernel.h>
#include <zephyr/device.h>
#include <zephyr/drivers/sensor...
Hello,
I have developed a Zephyr BLE project with the MAX30102 sensor. I tested the code successfully with the nRF52833 DK, and it works fine. Now, I am trying to flash...