I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello, May you please help me to understand how to enable the correct mode for testing. This what the laboratory request - "RF frequency fixing software and guidelines of...
We would like to drive two ps/2 interfaces via nrf52840 gpio pins (i.e., reading the protocol bit by bit, via gpio interrupts). A trouble is that ps/2 is timing sensitive...
Hi
I have some questions regarding the 32 MHz crystal on the nRF54L15:
If my firmware is configured to use external capacitors, will the very first crystal startup...
Hi,
I am developing on nRF54L15-DK BM (bare metal) for another board with a different pinout.
I need to disable the the MCUMGR log that prints to UART TX pin 1. 04....
Hi,
I am working on Google fast pair locator tag using NCS sample code. For final product, we need one function in device for certification that is to disable and reenable...
Hi nordic support:
Our product used nRF52840, we tried test nRF52840's BLE OTA RF performance with CMW500. After the nRF52840 device is assembled with the casing, it is...
We have a custom nRF5340 board that interfaces with an MT29 NAND Flash IC over the SPIM3 peripheral. Our DFU solution involves storing update and rollback images on this external...
I'm developing on the nRF54L15-DK using NCS3.1.1. I've recently encountered a strange behavior.
My program writes to the RESETREAS register. A bus fault sometimes occurs...
Hello,
Following the ongoing many issues to make Ethernet work alongside the modem on nRF9160 ( , , devzone.nordicsemi.com/.../ (clicking “Convert to public” on this one...
Hi !
I've been through a lot of documentation but did not find any matching my case.
I'm using a custom board with an NRF9160 chosen for its ability to connect to LTE...
Hello,
I want to use P0.10 and P0.11 for SPI purpose for my custom nrf5340 board.
But when I clear the forwarder property for these pins from the pin editor gui, I am...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hi Support:
I am testing channel sounding initiator on our board, but there is a crash on CS initiator starting.
below is log:
uart:~$ initiator on [00:57:24.604,598...
Hello,
The Altium lib provided with the DK, has two geometries, one with an "_2" at the end, what is the difference between these? (if any).
Thank you,
Beleni...
