Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello everyone,
I have been trying to get the nRF9160 DK connected to Edge Impulse Platform but it is not possible. i have been following this viedo Connecting nRF9160 DK...
Hello,
I have understood that the pc-ble-driver library is currently in maintenance mode[1] and not getting new features anymore.
We are using pc-ble-driver-py library...
Hello Nordic support,
I am planning to develop an application that will either use Zigbee protocol or BLE protocol. The protocol to be used is determined at startup by reading...
Hi all!
SPI3 Slave project is not built - error:
identifier "__device_dts_ord_DT_N_S_soc_S_peripheral_50000000_S_spi_c000_P_cs_gpios_IDX_0_PH_ORD" not determined
C:\ncs...
Hi,
I want to measure CO2 in different locations using two similar CO2 sensor ( MiCS-VZ-89TE). I can communicate with the sensor over I2C0.
But because two sensors have...
We are facing an issue in nrf52840 (SDK 15). Our hardware uses timer, SPI, USB, FLASH and uDMA. implemented watchdog timer and its working fine as well intented. But in some...
Hi I hope you can help me with this.
I'm using a nrf52833. When I build I see Flash usage of 278044 B.
Regions Size 512KB.
My custom board has this in the Flash0 settion...
Hi DevZone, I am using the nRF52840 to interface an ADS1298 (ECG Chip) via SPI.
I want to test if the communication between the devices are working by:
- Sending a RREG...
Hi All,
How do I disable the BLE stack completely such that I can switch to the DTM stack (DTM example using direct nrf_radio calls)?
Current I disable advertising and...
I want implement beacon function on my Qualcomm BSP board.
However, I'm testing with nRF52 DK in advance.
And need DFU OTA update for my F/W application.
So I'm implementing...
I am trying to configure the nrf5340 audio example to add the ability to update the firmware using a serial connection.
In the audio example documentation, there are a few...
Hi everyone,
I called "bt_gatt_notify()" from workqueue. Usually there is no problem, but when move far away, "bt_gatt_notify()" doesn't return. I called "bt_gatt_notify...
Hi, I'm currently using the Direction Finding Connectionless examples to evaluate using the nRF5340 for numerous projects we have lined up, and I'm having difficulty ascertaining...
