Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi All, Today I am migrating my project from ncs 1.9.1 to ncs 2.0.0.
The project was building find with ncs 1.9.1
But I do got this build warning with ncs 2.0.0: Any idea...
Hey guys, I was looking for a similar issue, however, I haven't found something like this (maybe I am searching for a case similar to this in a wrong way) But essentially...
hi all,
I learned that the Zephyr controller can connect to more than 64 slave devices and was wondering if it can simultaneously connect as a slave to the phone via ble...
Hey Nordic,
I am using
SDKv17.1.0
VSCODE as IDE
S140 as softdevice
Windows
Let me first insert my code snippet:
Here, NRF_LOG_INFO() function works, meaning...
Hello, I am trying to save data on an microSD card using SPI1. I am following the firmware in this discussion Working NRF9160 SD Card Example on SDK 1.9.0 . In addition I...
Hi! I used NRF CONNCECT to connect the Power Profiler Kit II, I opened the "Bluetooth Low Energer" app by mistake, and received a prompt to update the firmware. I chose to...
Hello Team,
We are looking to buy SOC which supports Bluetooth LE audio in a idea of developing broadcasting audio to multi devices.
Its understood that SOC RF5340 supports...
Hi Nordic engineer About the I2C SDA signal, when CLK voltage change then the SDA will occur skin needling，could you please helo explain it, I check the PCB latout, the I2C...
Hello ,
I am a firmware engineer in Taiwan ,
I already use nRF52820 to finish one case ( cheaper alcohol/acetone BT checker.)
Now ,the engineering stage is pre_production...
I am using SDK 14.2.0 with Segger IDE.
I am trying to configure timers and while my code does compile w/o errors the linker fails with message in the subject above.
To...
I see that nordi is working on wifi 6 .
When It will be available and on which platform ?
Is possible to have presentation on wifi 6 versus wifi 5 and BLE ?
Best Regards...
Hi
I want to use a Nordic NRF52840 to sniff and dissect a Digimesh network. Digi do not provide a sniffer or/and dissector for their products. There is no promiscuous version...
hello,
we are trying to use the stack guard module - obviously we want this to give well-behaved fault handling in the event that the stack gets too close for comfort. ...
Hi, I have a few questions regarding the modem module of the nRF9160 and considerations that might to be made when developing for it:
1. How does the modem determine which...
