Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I am using the https_client example for Thingy91. Everything was working fine until I tried to change the website to send https requests to (from example.com to google...
Hello Team Nordic, May I ask for your advice on how to build one nRF52840 to have two different UART connections to two different devices? May I ask for the any code examples...
Hi,
I am trying to integrate custom protobufs into the asset tracker project. I am referencing the zephyr/samples/modules/nanopb project for the same.
But I am getting...
HI ,
I'm trying to open terminal/command SDK v2.0.0 from toolchain manager (working with nrf connect for desktop v3.11.1) but it doesn't open.
while on SDK v1.9...
I'm just trying to make a simple communicatión between my nrf52 dk and my mobil using Serial Bluetooth Terminal app. I took the ble_app_uart example and I added a function...
Hi,
My project is a host micro (STM32) and a nRF52840 (controller mode) to implement a peripheral. My previous project (STM32 BLUENRG-M0 and host micro, HCI SPI interface...
Hi,
I'd like to add live audio streaming to my product, The current product consists of a sender unit and a receiver unit. Both using the nrf52833 (I've already bought 500...
hey guys i want to implement two separate application programs on the same chip.
Say Application1 is stored in address start_address1 to end_address2 and Application2 is...
Before using J-Link script to upgrade firmware, offsetStart (0x0) and offsetEnd (0x32E06) are correct. But after using J-Link script to upgrade firmware, offsetStart (0xADDEFE01...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to enable 2Mbps data rate. So I've added The following code in both peripheral and central.
ble_gap_phys_t...
I try to create new application using worspace type but fail , if I use freestanding type is OK. I already downlad and install SDK 2.0 . What happen? Could someone help me...
Hello, I just wanted to throw in that for a hobby project I created a PWM audio driver, with which one can play back 8-bit audio data very easily. Since it may be useful for...
hi
i'm new to the nRF platform and realised it uses zephyr. i come from a pic & stm32 background with little rtos knowledge and find the official zephyr cryptic. especially...
I created a BLE device with custom characteristic showing the sensor value (int16). But I can't achieve 1khz sampling rate.
1. Is sending data via NUS faster since the central...
I would like to using Keil to build secure_bootloader project for changing NRF_DFU_BLE_REQUIRES_BONDS from 0 to 1. But Keil failed to build. Please refer to snapshot of Keil...
