Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi !
I use the NRF52832 and with Segger Embeded Studio to code.
The problem I have is that for some reason, my uart don't work after using an I2C write protocol and I...
Hi,
I tried to send a packet larger than 20 bytes by calling bt_nus_send on peripheral_uart but failed.
After checked on DevZone, I found some similar problem and did...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
Hello
I try to write functions to modify the publish and the subscribe addresses. Unfortunately not all is working, attached you will find my code.
Problems:
1.pubish...
Hello
I'm using nrf52820 chip with Segger embedded studio and nRF5_SDK_17.1.0_ddde560 also soft device "s112_nrf52_7.2.0_softdevice" .
I want to add DFU through BLE support...
Hello,
nRF52840, SDK17.2, keil5, EC11 codec button
Output the same log in the positive and negative directions,
Turn one space: <info> app: cnt=-1 acc=1 accdbl...
Hello Everyone,
First of all, what a terrible experience this has been. I'm trying to use custom RSA private key in order to sign the firmware before we go into production...
Hello,
I am supposed to get to learn the nRF52840 DK, so I can start programming with it. I managed to build an executable for the blinky example using make in the Terminal...
Hi,
I'm having issues debugging a case where the device is reset / rebooted every 1-2 days on average for some reason without any error message as to why. If any error is...
We are porting a project from SDK 11 to nrf5 SDK 17.0.2. We have also used a couple of different versions of SDK 15 extensively on several different products.
Our code...
Hello, I'm trying to setup simple UART reception (interrupt driven) with Zephyr OS.
When a message over UART, only some characters are received, others just skipped.
Here...
Hey,
I am planning on using the Nordic SDK for some distance measurements between two nRF52840 boards.
For my documentation I would also want to understand how the technology...
Hi Folks,
I am bringing up a new printed circuit board with a Fanstel BT840 (nRF52840). When I install any firmware, even Blinky, it simply gets stuck in k_cpu_atomic_idle...
