I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi
Is there a possibility to read out the actual RX pointer of the DMA if the amount of chars is not reached?
Start Stop the RX is not really an option and I have no...
Hi everyone! I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice. The nrf go studio can not detect the nrf52832, but...
Hi,
I set sending of Ext. ADV at a periodicity of 500ms and scanning for 100% time by setting same interval and window configuration to 2.56 s.
But I observed that the...
Hi
I have a project to use HID mouse and keyboard at the same time, I have tried , but it really can't work well. I've read the similar question and you don't give the clearly...
Hi
I want to combine mouse and keyboard function together,and I had modify the example of hid mouse,show as below
but the question I meet is that the PC and phone reaction...
Hi,
I am developing an application (Peripheral Sensor device: Acceleration measurement), I have included the characteritsics for the measurement and I am trying to include...
I tried to enable the configuration of Thingy91 to use external sensors. I made following additions:
1. Added the following line to Asset_tracker_V2/K config file : rsource...
Hi,
is it possible for a central device to connect to a peripheral device directly (without using nrf_ble_scan_init( ), nrf_ble_scan_filter_set( ), nrf_ble_scan_filters_enable...
Hello,
I am trying to write some code that sets the BLE Tx power on the nRF52833 SoC.
I have based my code on the sample example code provided at C:\Zypher\v1.7.0\zephyr...
We're using the read authentication trigger to detect when a characteristic is being read, so we can update the value before a read. Is it possible to have a read with zero...
Hello,
at the beginning I want to state, that I have read all the tickets with similar issue, but still can't find any solution to my problem, that's why I'm creating...
Hi!
I was controling a little vibration motor with a mosfet which is activated by a nrf52840Dongle pin. I was using pin 0.17 and it worked pretty well, but now I am trying...
Dear reader
We want to use the floating point unit (FPU) in our project
We are building using the IAR compiler (8.5.x)
We'd like to use the hardware acceleration ...
Hi.
We are working on a project which uses nrF9160DK and nRF5340DK, which works fine on this last one. The problem is that when I tried building on the 9160 using nRF Connect...
