Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello, i'm using nRF52833, pca10100.
I would like to connect multiple peripherals by referring to the mulit link example.
First of all, I'm going to try to connect to...
I'm trying to use the I2S peripheral on the nRF5340DK. It looks like the zephyr drivers don't currently support this board, so I need to use the nRFx drivers. I've ported...
Hi everyone,
I have a custom board based on nrf52840, the Fantsel BC840. I have created my custom board, changing assigment of pins for leds, buttons and UART0 on custom_board...
Hello Community,
I have nRF52840 board. When I connect board to system it not get detected.
I tested VCC supply it is OK.
COM port is not seen anymore.
I tried to...
Hi Sir/Madam,
Our application needs to be running on both cores and the network core needs to use some crypto algorithms provided by the crypto cell. From the data sheet...
Hi, dear Nordic & all：
I found nrfx_saadc_uninit() did not work when use SAADC's differential mode with SDK17.0.2, nrf52832, the fellowing is saadc init and configuration...
Hi, there:
based on \\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132, I need add Just-Works bonding function. But this bonding request need launch...
Hi
I am using nRF5_SDK_17.0.2_d674dde with softdevice S140 have sample example as ble_app_template_c but when i run the code i get the following below error are as follows...
Hello,
I am compiling my BLE project on nRF5340, with nRF Connect SDK v1.6.1. I got this error: undefined reference to bt_gatt_exchange_mtu.
My code works fine on SDK...
11:14:55.624
Received status with code 0 PKT_SEND_MAX_RETRIES_REACHED, message: 'No response from device. Tried to send packet 6 times.'
11:14:55.954
Server setup...
Hello,
I am looking at the Asset Tracker v2 example and was wondering if it is possible to use the A-GPS or P-GPS services offered through nRF Cloud if I am using AWS or...
Hello,
Both parts part#nRF9160-SICA-R and nRF9160-DK are available on Mouser website but t he customer would like to check what revision is.
Could you please help to...
