Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Dear Nordic company,
I am not able to compile any of my applications I was able to compile. Yesterday, everything works, but today, it doesn't work. I tried older version...
Hi,
I am currently trying to integrate a digital microphone with the I2S peripheral of nRF5340 audio DK. I am accessing the P10 header of the nRF board for the particular...
From the examples of SDK 17.1.0 (I'm Not using Zephyr), I'm trying to connect to a beacon's Generic Access Service, so I can read the characteristic 0x2A00 and then read it...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hi, i've setuped Clion to build my porject. I've followed this link . Everything works i'm able to build for my custom board, but in zephyr folder I d'ont see merged.hex file...
Hi,
according to the known issues list for the SDK release 2.5.x x=[0,1,2] and others previous ones, the bug NCSDK-21379 exists (see the link below)
https://developer...
Hello, My SDK is NCS2.8.0, I want to know the version of matter, but I can't find it, may I know how to get?
BTW, does NCS SDK support Matter 1.4.0, if yes, could you tell...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Build configuration is: SDK: nRF Connect SDK v3.0.0 Toolchain: nRF Connect SDK Toolchain v3.0.1 Board target: nrf52833dk/nrf52833
All other values left at defaults.
There...
I had like three Thingy52s for a project and have just come back to it after about a year.
The batteries are now dead and the device does NOT seem to want to charge.
All...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
