Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am using a STlink to flash a nrf51822 module , and i am using Keil to do that, i flashed the module but when i am scanning it to find it in my mobile i cant find it, i doesn...
Hi ,
Does the Application update depend on bootloader version? . I changed the boot loader but application remains same on my device , hence the device is not booting up...
I have an application with three other tasks beside the sdh task. I'm trying to integrate softdevice to my existing freertos application, but soon after the task scheduler...
Hi,
What would be the procedure for updating the firmware of device through another host micro controller UART? (Not with PC tools like nrf go studio, nrf connect, nrf jprog...
Sir,
I have a MDBT50Q-UFL evaluation board. I am using Keil uVision 5 and flashing is done through ST-Link. I downloaded the example files from http://developer.nordicsemi...
Hi,
I have Ublox EVK-NINA-B3 on table, which has totally different pin layout than NRF52 DK (not sure why): https://www.u-blox.com/sites/default/files/EVK-NINA-B3_UserGuide_...
Hello everyone! I am a beginner and I need help in understanding advertising data. I am migrationg from SDK 13 to SDK 15.2. In SDK 13, the advertising data with manufacturer...
Dear Engineer,
work on sdk15.2, pca10040 eavl board. one as central run this code
\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\ble_central\ble_app_multilink_central...
I am starter developer of nRF51822 custom board.
in this board 16 mhz crystal is connected externally with XC1 and XC2 pins(37 & 38)
nRF5_SDK_12.1.0_0d23e2a rar file is...
Hello everyone,
I know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet.
For example: https://devzone...
(Mesh_v2.11, SDK_15.0.0, NRF52832)
Hello,
I wonder if a device can relay DFU packets even though mesh_relay is disabled by nrf_mesh_opt_set(NRF_MESH_OPT_NET_RELAY_ENABLE...
I am trying to set up the nrf52840 dongle on IAR using an I-jet for debugging. I have iar version 8.32.1. I am using example project ble_app_blinky from the ble_peripheral...
Hi I met a problem during programming a combo of HID on nrf52. I have set combo HID that have keyboard and multi touch. after pairing my smartphone(galaxy note 8), keyboard...
Dear Colleagues,
I'd appreciate your advice on the selecting external or internal pullup or pulldown design for a wake up button which would cause minimal increase in current...
Hi.
I'm trying to make a bluetooth based sip/puff controller for disabled people. The main use case will be to enable people that can't use their hands, but move their head...
