Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello,
I'm working on nrf5340 audio bis gateway sample.
The NCS version I use is v2.2.0, I know it's a very old version, but for some reason I can't update to the latest...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hello,
With the latest version of the nRF5340 MDK I am getting the following linker errors (below), and don't understand why they should turning up.
Best regards
==...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I need to use ADC in the project, and then I have configured ADC in overlay. The code is as follows
The same code can be measured normally in Zephyr's ADC example, but...
Hi,
I'm trying to use an nRF52840 dev kit as an I2S-to-USB microphone, but I've been running into a problem where the recorded audio is periodically unusable.
To debug...
Hey Everyone ... Looking for some ideas / help with crash involving nRF Sniffer v2 and Wireshark. Specifically I have an older White MacBook that I use for sniffing and nRF...
Hi,
I am using sdk 16.0 and I am already using 3 SPI Instances i.e. SPI1, SPI2, SPI3. I wanted to use SPI0 Instance also. How to use it?
If enable SPI0 in sdk_config I...
Hello
I was working on nrf9160-dk with assert_trakker_v2 application successfully connecting to nrf Cloud. There was no problem.
Today I started the day by deleting it...
From what I understand, the nPM1100 can work without the battery (i.e. no BAT connection).
Does the Nordic Thingy:53 come with the Li-Po battery separated or is it mounted...
Good afternoon everyone, how are you?
I'm using custom hardware, Nrf52833+Nrf21540, already reviewed by and tuned by Nordic. We are going to carry out the tests for product...
I need to work on single bank DFU from esp32 to nrf52833. I found a website with instructions on single bank configuration here: academy.nordicsemi.com/.../topic /exercise...
Hello,
i'm working on a project where the system will be always in deep sleep unless there is an external event to wake him up. Upon this event, the system connects through...
Hello, I have a question about how to operate on multiple Zigbee devices simultaneously. I am currently developing a hub to control and retrieve data from home appliances...
I want to make a secure pairing with Bluetooth. Let it first pair with the device, then connect directly without pairing. Maximum how many devices can I register?