During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi folks,
I'm having some UART trouble - help would be much appreciated, and thank you in advance.
------------------------
Overview:
I'm working on a project that...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Hi,
Is there a way to make the main thread to execute after any interrupt?
For now, I have something like this (ncs 2.7.0):
in main thread :
In each IRQ handlers...
Hi,
I am sending 20 bytes of data in a beacon format. These are fit into m_beacon_info[2] to m_beacon_info[21] defined in ble_app_uart code from nordic SDK:
I send beacon...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hello All,
I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup,
https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. We have a project using the nrf52840, which is sometimes used by carriers. I ported radio_test to...
Hi
I am using HCI Power Control sample to dynamically control TX power. I found that the TX side's connection RSSI and RX side's are diferent, at some point it even has...
Hello, I'm trying to follow this example (Serial DFU) , on a nRF52840 custom board, but I'm getting the following error:
I couldn't find any relevant information and also...
Hi,
I have recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. To begin, I used the "Hello World" sample code. While I was able to successfully build...
I have searched everywhere and can't find a working example that shows how to create a new BLE ID and save it to the setting s partition.
Please show me the configurations...
We have a custom board that I ran through the board_v1_to_v2.py program and then attempted to build under SDK and Toolchain 2.8. When I run it it failed in the CMakeLists...
I am incorporating the nrf52840 into a new design and it is my first time working with a Nordic product. I am looking to start with the SEGGER J-LINK EDU MINI due to it's...
Product: nRF54L15DK, SDK V2.9.0
Application: Multi protocol (BLE + Matter/Thread) Door Lock
Issue: BLE bonding is not retained after power cycles. The mobile app requests...
Hi,
I am debugging the zigbee functionality and would like to enable the zigbee log,already enabled log in prj.conf but no data coming out.What do I have to do to enable...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
hi Nordic teams:
we meet one serious issue about LSM6DSL FIFO reading, our product (host mcu is nrf52840) need to read lsm6dsl FIFO data periodically with one second interval...
