I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello,
Using this link ( https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral ) I'm able to add passkey protection...
Hi,
i have found similar posts on the forum but could not find the answer. Therefore,I think it is necessary to raise this question again.
problem: platform:nRF52832 and...
Hello there,
I have been testing on nfc-uart example of SDK 13.3.0. I am trying to pass the buffer of 258 bytes to pointer "p_pdu" and its size of 258 to "pdu_lenght". ...
We would like to have that all communications, programming, and supply related TPs and SBs should be kept for debug purposes. Otherwise, we would like to remove all unnecessary...
We're working with the NRF5340 PDK, and it's a pretty big library change from the old SDK. So far I've been unable to find out where to configure the bluetooth PHY and link...
Hi everyone,
The task is as follows. I set up data transfer using notification. I transmit ~ 83 kB in ~ 10 sec. The connection interval parameters are as follows:
The...
Hi Guys,
I flashed the ble_app_uart example available in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10056\s140\ses location to NRF52840 DK board. In...
Hello,
I have been trying to get RTT to work with the nRF52810 but trying to compile the examples leads (as usual) to errors because there are a load of libraries and files...
Here is my program：
#define EXIT_PIN 31
void EXIT_Init(void) {
nrf_gpio_cfg_input(EXIT_PIN,GPIO_PIN_CNF_PULL_Pullup);
NVIC_EnableIRQ(GPIOTE_IRQn); NRF_GPIOTE->CONFIG...
Hi,
Our project is 2D-3D mouse. we are using nordic "ble_hid_mouse" application with some required changes for our application.
SDK we are using is 15.3
ISSUES ...
Hai,
we are using nRF52832 and Nordic connect for our development and testing work
we are facing disconnection issue on android after ~3min so we changed the CONNECTION_MIN_INTERVAL...
Hello,
I tried to configure Ozone for aws_fota sample without any success. I loaded elf files but one is debuging mcu boot and the other never access to the main. Do someone...
I just get one NRF9160 DK(PCA10090 0.9.0) to test the default asset_tracker application with Basis Simcard in the Oslo area. The modem firmware is mfw_nrf9160_1.1.0.zip. I...
