Hi,
we are looking into incorporating a NRF52 module into our control units, but to allow extending the antenna position away from the case through male-female SMA cables...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello Everyone,
I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20?
void NRF24_AdressTX...
Hi all,
I'm working with my custom nRF9151 board and i'm testing https request with option that use native TLS for my download client.
I got connect err = 22, so i come...
Hello,
i am currently trying to build a minimal firmware for the nRF5340 on the Thingy:91x. Unfortunately my build failles to link zephyr/zephyr_pre0.elf:
My suspicion...
On the nRF54L15, how can I update the maximum TX time to 17040 µs when using Coded PHY?
I'm currently testing with the Throughput sample in nRF Connect SDK v2.9.1. During...
Hi,
I'm making device with nrf51822 chip and 400mA battery.
It connects to smart phone.
It has to calculate heart rate and some other things, so it's doing it on device...
Hi All,
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to...
Dear all,
I tried the example program ble_app_uart given in the examples section of the Nordic folder in Keil installation. I created the hex code and programmed my chip...
I was just at the Nordic nRF52 Global Tour in Atlanta and I received the nRF52 Development Kit (PCA10040). One of the Nordic engineers mentioned that the nRF52832 is at rev...
Hi all,
I am using the BLE nRF8001 and EFM32 (ARM Cortex M3). I used the following SDK for connecting the modules using ACI (SPI). github.com/.../ble-sdk-efm32
Now I...
brownout reset = 1.7V
Operating conditions VDD(Supply voltage,internal LDO setup) = 1.8V
(by 1822 Product Specification)
In between 1.7V of 1.8V, or it would have been...
Greetings, I've been using the ARM GCC tools for about 2 months with success for programming the NRF51 DK board. Now I would like to try out the example found in:
examples...
I run step by step the example of adding DFU to ble_hrs, everithing runs fine.
I try to change in the same way another example, ble_app_proximity.
The problem is that...
Hello everyone
i have created one custom service and i succed to compiled then i checked my service via master control panel it is showing unknown service but i named it...
Hello,
I have a question about including multiple identical services in GATT table. For example, my device has 2 batteries so I need 2 battery services (with same UUIDs...
Hello,
I am developing a NRF51-based peripheral (S110) device with N tactile switches - each one assigned to single "bonding slot". I need the peripheral to be able to...
i have use nrf51822
when no connection creat between android nrfUart app and backon kit so autometically sleep in 180 seconds,
but i have need sleep condition in connected...
I'm new to the Nordic range of devices and the SDK.
I have a project where I'm using the HAL in the SDK to configure GPIO/GPIOTE and the UARTE0. With both the GPIOTE and...
Just want to check that my understanding is correct:
I have ported/migrated my app from SDK 6 to SDK 9, merely because I want to use the DFU facility. However, I have read...
