I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Does anyone know why I am getting low outliers on battery measurements with the SAADC? I am measuring the battery directly every minute. Every seven minutes consistently,...
HI,
To ensure NRF5340 2.4G rf consistency during mass production, which scheme do you suggest is more suitable （ X2 = 32MHZ 10ppm ）:
1、Offset capacitance C36 C37 placed...
I used Modem firmware version 1.3.1
In order to connect the nrf9160 DK to the AWS cloud, I am encountering errors such as AWS_ IOT_ EVT _CONNECTING, when it should be AWS_...
In a nrf52840 project using Zephyr 3.0 following Zephyr drivers are used:
the modbus serial driver(RTU mode) which uses uart1 in interrupt mode
the lora-mac driver which...
Hi,
I'm using app_ble_uart example using nrf52810 for nrf52810 UART RX & TX pins are (P0.15 - P0.14) while configuring using i got a problem with RX transmission ,when i...
Hi,
I am working on a multiple custom models, wherein I need one model to extend the functionality of another model.
I was analyzing through nCS provided "Chat" sample...
Hello,
I'm running nRF Connect SDK v1.9.0 on two nRF52840-DK devices, one Peripheral other Central.
My application requires to initiate pairing, i.e. send pair request...
Hello,
I'm trying to set up nRF Connect for VS Code. I followed this video for installation steps: https://youtu.be/2cv_jjqk5hg, the only difference being that my nRF Connect...
I have a VS Code project that is a Workspace Application where I've had to make some modifications to code in both zephyr and mcuboot directly. My codebase is in a git repository...
Hello!
Do you have any information on the antenna itself? Radiation pattern-diagram?
Edit: I would also like to have the specs of the antenna, eg: m ismatch loss, insertion...
I am having trouble to add the toolchain folder to the VS code setup.
The nrf connect for VS code does not pop up on the side at all to add application folder.
Tried to...
Hi guys,
I try to integrate the flash logger backend .
When I run the code I get the following error:
<error> nrf_fstorage: addr_is_within_bounds(p_fs, dest, len) check...
Greetings. I am developing a application that will run on a custom board based on the nrf52833 MCU. During development we have been using a nrf52833 development kit for testing...
Mr. Jared i do apologize for having accidentally verified&closed the issue but to answer your question we've found that the module we were using did not possess a 32khz crystal...
Hi,
I am using the code provided at https://devzone.nordicsemi.com/f/nordic-q-a/85850/example-for-extended-advertisement-receive-node
to send more than 60 bytes, but unable...
