I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
i need to store few configuration bytes in non volatile memory. I found out there is settings module that can be enabled in Kconfig GUI (SETTINGS option).
My use is...
Hi,
I have successfully programmed the nRF5340 Audio DK as a gateway device using the Command Line Tools and by using the directives listed in the 'nRF5340 Audio' program...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and have run into an inconsistency I'm hoping...
I have an application where I need to trigger time critical SPI reads of accelerometer data (sample rate is very crucial and data is fed into a FFT). In my current SDK based...
Hello!
I have added a UART and I2C to the Mesh Sensor Server example and on a custom NRF52840 board everything works fine.
Today I tried to add SPI without success.
...
1. Hi currently i am using nrf52840 sdk ver 17.1.0 s140 sd we have added UART in the secure bootloader/ Bootloader_ble_debug
2. we can able to send multiple bytes once ie...
I am trying to interface my PDM mic (ICS 41351) for a week now , and only got erros . Please direct me to a simple Project Code to use PDM mic with my nRF52840
Hello,
I am working on unidirectional voice broadcasting device where the maximum range is the priority. At this time I am developing on Audio DK boards.
I need some help...
Setup
nRF9160-DK
PCA10090 1.1.0 2022.4
Modem FW: mfw_nrf9160_1.3.3
Asset Tracker V2, I tried both the downloaded version from here: https://www.nordicsemi.com/Products...
I'm trying to send a parameter over BLE, but once i've stopped using the BLE stacked (and unininited softdevice) I can't seem to save the parameter recieved with pstorage...
Hello, I'm running the nRF5 SDK's ATT_MTU throughput example and I want to check that the data sent by the 'tester' (nRF52832 in my case) is effectively received by the 'responder...
I am trying to use mpu6050 with nrf52840, using bare metal programming. The program gets stuck at this loop -
while ( NRF_TWI0 -> EVENTS_TXDSENT == 0 ); what is the problem...
Hi! Firstly I am somewhat new to developing on nordic chips so I'd like to apologise in advance or any silly mistakes or oversights I may have made. I am currently working...
Hello
I've previously developped a BLE peripheral product with a nRF52840 chip. I've been able to do everything I wanted for my peripheral and while I was making it I...
How to determine if the download is complete when downloading files from the FTP server using the ftp_get function?
Although Ctrl_cb will return code, in my actual testing...