I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
I have a question: Is it possible to use BLE Long Range mode (Coded PHY) in the NRF52840 with mobile phones? If not, is there a solution to use it in parallel with normal...
I am using NRF52840's NFC with apple wallet but it requires certification from Apple to be used as tag reader. How can I get it certified so that I can read data from apple...
Hello,
I need to be able to send/receive binary data over this BLE UART Service (bt_nus) on macOS. I'm using the peripheral_uart sample project with no success. It seems...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
Hello all,
We're on the initial stages of a design that requires Wifi (ideally) in a very challenging environment, where in the worst case scenario the temperature could...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
I have a BME688 connected to a NRF52840DK and I cannot get a working I2C communication using Zephyr. Below are all sources:
app.overlay
main.c
prj.conf
I was...
Hi.
I am trying to disable the RESET pin (P0.21) on the nRF52810 microcontroller (custom board) and set it up as a normal I/O pin.
I'm using the SDK v2.6.0.
I don't...
Hi, my device is central device( Central UART ) and I couldn't get stable pairing with peripheral device with display which provides passkey code. The scenario: 1. From the...
Following instruction here for setting up NRF52840-Dongle as a radio coprocessor for use with OpenThread Border Router.
The error is at the second step when executing "...
I'm alter the overlay file to adapt my board.
In my board,I try to use pin 9,10 as uart_tx and uart_rx,without cts and rts.
I wirte it in my app.overlay as follow:
...
I am currently working on a project where I need to connect my nRF52833 microcontroller to other devices using the Nordic UART Service (NUS). I am using the nRF SDK and Segger...
Hi,
I created a custom board following the instructions from https://www.youtube.com/watch?v=V_dVKgWKILM . Everything is ok and with the "Hello world" example builds without...
Hi,
We have our custom PCB with an nRF9160 SIP that is connected to a nRF9161-DK via P20. I have a couple questions about this setup.
Is it fine for us to program...
