I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I have a problem with timer 3 of nrf52820.
It concerns a trailing edge dimmer implementation based on timer 3. A gpiote is used to sync the zero crossing.
I use ppi...
Dear Nordic-Team,
I designed a custom PCB using the nRF9151 as the host processor, the nRF7002 as a Wi-Fi companion, and the nPM1300 as the power management IC. The Wi-Fi...
Hello,
I encountered a strange behaviour on a nrf52832 : - I flash a a debug firmware (with debug optim in build config) : I can run debugger and add breakpoints - I stop...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
Hello, I am not sure if this is the most appropriate place to ask this question, but any comments are welcomed. I am developming a sensor platform that tries to use extended...
So hello everyone, I am a computer science student with zero IoT background. I am trying to a wearable device . I want to nrf52840DK with max30102 heart rate sensor and communicating...
Using nRF5 SDK 14.0.0 with Softdevice s132 v5.0.0 on nRF52832.
I've set up my nrf to be a GATT client (in central role), and I'm using bluez on my Linux desktop with a...
Hi,
we have a NRF52832 based project / product. We are using a DFU bootloader for application and SD update. The update is done from a master microcontroller using UART...
Hi Devzone,
Currently, we are attempting to use the Generic three-wire coexistence (refer link: https://docs.nordicsemi.com/bundle/ncs-2.9.2/page/nrf/app_dev/device_guides...
Hello,
I am working on a project which was previously developed by another person, and am struggling to setup the development environment. The project was built on nRF Connect...
Just got myself a ppk2, tried to set it up on linux, it wanted to update itself that didnt work on linux. On windows it did. Then tried to connect and it just keeps loading...
Hello,
I am currently working on a BLE Mesh–based control system and would appreciate guidance on a few architectural and scalability concerns.
System Overview The network...
According to the working principle of a crystal oscillator, the load capacitance is inversely proportional to the resonant frequency of the crystal, that is, the larger the...
