I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Environment: SDK v3.1.1 with a custom board based on the nRF52840.
I wrote a test application that I've been using to verify the hardware on a custom nRF52840 board. I have...
Hi,
We are using an nRF52832 in a bare-metal project. (No SDK)
We have three input channels to the ADC that we wish to use. These must be oversampled. (256x)
To simplify...
Hi guys,
I'm trying to do FOTA updates on my board and I was able so far to download the image but not able to apply it.
I've followed the academy FOTA over WiFi example...
I've got an example code to turn on an LED with a button, it works. When I change it to send an spi command, it doesn't work anymore.
Could you check if you see something...
Using;NRF52832,
SDK17,
Flutter 3.10.5 ,
nordic_dfu : 6.0.1,
iOS 16.5.1
iPhone 14 Pro Max
Using my developer device I can successfully update DFU,
However on...
I flashed the same code to the two nrf5340dk but i get the below output , with out any changes in the example sample code. it gives the serial output every time E: IPC endpoint...
I have installed both sdk 3.0.0 and 3.1.1 but both of them give me the following issue:
Upon building, the error given above shows for some reason but this is not my own...
Hi,Team,
I am currently using the nrf5415 to develop OTA. My NCS version is v3.0.2. Now I have two types of devices: Hub and Terminal. Both of these devices use nrf54l15...
The uart output of nrf52840 dongles is corrupted, including no lines separation, strange characters. for example:
5E0 to 1:00000000148A0C90 [18FF] [UDP:�]�8~~[fdbc:dc24...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello, I am currently debugging with nRF52833 and nRF5 SDK, and I have a few questions to ask:
I want to time-share the BLE function and the ESB function on a single MCU...
When I2S reads the digital audio sensor, when strat is turned on_ After I2S, the data can be read and recognized normally, but this action takes up the whole CPU occupancy...
Hello Nordic team,
I have a question related to the “nRF5340 Production Programming – Troubleshooting” documentation, specifically the part that says the access port protection...
Per (+) Trouble with nPM1300EK - Nordic Q&A - Nordic DevZone - Nordic DevZone , I've disconnected TWI from the board while doing the battery profiling and that worked successfully...
