I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
hello,i now get the IQ sample frome my DF demom, i use the putty to see the IQ sample.Here is my output in putty.
yes,i also use the python procedure of serial moudule...
I generate my keys add the dfu_public key to the example found in examples/dfu/secure_bootloader/pca10056_s140_debug. I then connect the board, erase all and program my nrf52840...
Hi
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
I am new to BT and USB protocols.
As part of our POC I eed to test and establish...
Hi,
I have implemented a set of custom mesh models on nCS. In vendor models we have reset handlers, as in nrf documentation: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
We cant get a connection to our Matter Development Board like in the discription: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/connected-home-over...
This may just be more of a Zephyr question but wondering if anyone in the Nordic community has experience with this.
I'd like to generate code coverage reports when running...
Hi,
I'm developing a board based on the thingy91 (same nordic silicon, different sensors) and using nrf SDK v2.0.0
The blinky application is flashed and run correctly...
Hello, I am using the nRF connect SDK and am currently running into some issues with using the on board ADC. My issue relates to the adc_channel_setup function which returns...
Hello,
I am using an nRF52833 dev kit and the Zigbee light_switch example from nRF Connect SDK.
I was trying to implement the sleep mode so I wanted to estimate the power...
Hello,
I am having an issue with board bring up for a custom board I developed using the nrf5340 processor.
I have created firmware based off the peripheral_uart sample...
Dear Nordic support team,
I bought 3 piece of nRF52-DK from MOUSER, 1 piece of nRF52-DK version is 2.1.0 , and another 2 piece version is 3.0.0.
nRF52-DK version 2.1...
Hi there,
We're using nRF52840, IAR 8.40.1, nRF5_SDK_16.0.0_98a08e2. My question is, I need to toggle a GPIO pin right after SPI finishes the TX transaction and right before...
I am trying to use both USB and BLE on an NRF52840 using SDK 15. It hit a hard fault during initialization, specifically when it tries to enable the USBD IRQ.
It looks like...
I am familiar with the PTCRB certification process for an IoT device incorporating a certified module. https://www.ptcrb.com/wp-content/uploads/2020/08/10_Steps_to_PTCRB_Cert_for_Cell_Enabled_IoT_Devices...
