Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi, I'm using Segger Embedded Studio for developing farmware of nRF52840.
and, using
nrf5_SDK_for_Mesh_v4.2.0_src
nRF5_SDK_16.0.0_98a08e2
I would like to use "es_battery_voltage...
i wish to change P0.13 as tx, P0.15 as rx , P0.17 as ctx , P0.20 as rtx
I change in bsp definitions and it worked for uart peripheral example,
I also change pin...
Hello,
The USB connector came apart from the nRF9160 development kit soon after a purchase was made from Symmetry Electronics. Would it be possible to have the board replaced...
I have an RTOS application into which I integrated a custom BLE service code. Question is, there isn't any need for a separate thread for handling BLE stuff? I see BLE events...
Hi,
I am trying to use UART APIs in blocking mode to receive data from another controller.
I intend to have a timeout on receiving function so not to stuck if no byte...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I am investigating the data bit and stop bit settings. At that time, I found a page...
Hi !
I try to use VSCode but any examples return same error:
"Linking C executable zephyr\zephyr_prebuilt.elf FAILED: zephyr/zephyr_prebuilt.elf zephyr/zephyr_prebuilt...
Hi,
As the title states, VS code doesn't recognize includes related to Zephyr.
I've walked through the entire setup guide and installed all components using the toolchain...
So I came across an issue while working on developing an app that can update firmware OTA. I was using Nordic Semi - android DFU Library
implementation 'no.nordicsemi.android...
hi，
1.Now I am using Wireshark to capture nrF52840 DK ZigBee packets. I have configured the environment according to the guide. In wireshark, "nRF Sniffer for 802.15.4"...
hi，
we are using52833 QFN40 to test carrier,but the program will loop at as the picture bellow,while it runs well in 52833 QQFN73 in another board, why? Coutl you help me...
Hello,
Our modem consumes a lot of current when we use a simcard from a provider 1 (a MNO), much more that when we use a simcard from another provider 2 (a roaming service...
Hi,
with a custom hardware, I'm using a NRF9160 with a ESP8266 chip over uart with following prj.conf and board overlay:
I was trying to open a socket (that uses the...
