Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
New issue found, unsure if I can resolve this one! I have found the RTC1 may on rare occasion lock up, no love of resets, playing with LFSRC or RTC registers will make it...
Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
SDK v3.0.2 Toolchain 3.01
Is it possible to set the DIS name, (and possibly others) dynamically at runtime? I need to provide some level of configuration to my end users...
Try run Thread Certification with nRF52840 dongle, steps as below:
1. when Test harness is R62, Nordic devices work normally.
2. upgrade Test Harness to R63, and flash...
Hi,
We have 2 queries regarding I2C modes,
1. I2C fast speed mode
We are undergoing test of I2C under I2C_SPEED_FAST - 400Khz
when we enable this frequency on our...
Does ncs 2.5.0 implement the suggested workaround for https://docs.nordicsemi.com/bundle/errata_nRF52840_Rev3/page/ERR/nRF52840/Rev3/latest/anomaly_840_219.html ?
If not...
Hi
We met the problem is that clock low time period is out of spec, we got the value from oscilloscope is 1.24us@pull up resistor 10K/7.15k when clock speed=400kHz. The...
Hi
About nRF52840 I2C data read (CLK rate 400KHz)
1. Could you help check below three I2C items(tHD;DAT, tHD;STA, tSU;STO) can follow I2C standard(NXP) spec. or need follow...
Hi, having some issues with the matter door lock sample for the nRF54L15DK on NCS 3.0.2. I'm getting strange failures on boot when running the default matter door lock sample...
Hi,
using SDK 3.0.2 and build for the *ns target.
The idea is to put the CPU to sleep and while it is sleeping GPIO events (e.g. button press) shall increment a counter...
I have several applications that continuously scan on Bluetooth that have started exhibiting a new failure mode after upgrading nrfxlib from v2.9.0 to v3.0.2 ( https://github...
For our custom nrf9151 board,
The following is the prj.conf:
There are no pullups on any GPIO and for now, assume there are no peripherals connected, but there is a...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
