I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello,
I am encountering difficulties connecting to and recovering my nRF52840 board with J-Link on macOS, both via nRF Connect and using nrfjprog in the terminal. Below...
Hello,
We are using the nRF52840 dongle (PCA10059) with the CLI agent software as a Zigbee network coordinator, and the Digi's XBEE S2C as a Router.
We are using XCTU...
Hi Team,
I have nRF5340 DK board and I want to test the Bluetooth Periodic Advertising with Response and Bluetooth Periodic Advertising with Responses Synchronization...
Hi,
I am trying to create a new custom service in nRF Connect for desktop and play around with its characteristic properties.
I Use an nRF52840 DK as peripheral and my...
Hi,
Its maybe a stupid question but is there a easy way to operate the DK with 3V VDD and IO Voltage? The 9160 DK had a simple switch for this. The default for the 9151...
Hi everybody I'm using nRF Connect SDK 2.6.1. Before I could seen Partitions section in Memory Report tool, but now it's disappeared. I also checked it by ninja command: ...
Hello,
I have a few questions: 1. How to add a prj.conf or an overlay file to enable peripherals to use an external high-frequency crystal oscillator as the clock source...
We have developed a firmware application using the OpenThread library for the nRF52840, utilizing the Nordic Development Kit and Segger Embedded Studio for ARM (version 5...
Dear nordic support team,
after having migrated my project to SDK release 2.8.0, the following message appears in the logs:
<dbg> bt_sdc_hci_driver: configure_memory_usage...
"I'm working with nRF Connect SDK v2.2.0 for nrf52840 and I'm trying to implement file transfer functionality using mcumgr over UART in Application. I've successfully configured...
Hi , I flash periodic_sync_conn sample to A and B development boards, and periodic_adv_conn sample to C development board. Only A and C development boards work normally, but...
Hello. We are developing custom boards with the configuration of nrf5340 + nrf7002.
In the previous sta example, a build error occurs when the "Board Target" in "build configuration...
I have customed my own nrf54L15 board and it would run on button battery. I managed to measure the battery level through ADC, but I don't know how to use ADC with nrf54L15...
I've been working for months to try and figure out exactly how to get my application to bond the way I want it to.
I'm using nrf connect sdk 2.4.2 on an nrf52832. I used...
