Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
I'm trying to build the UART app with SES as per this example:
And I'm getting this error in SES:
Did I miss a step in the installation and setup somewhere?
Dear Support team
1) I find that there is a C9 in the nRF52840 reference circuitry for CKAA WLCSP which said that the C9 is not required for Fxx and later as the picture...
Hi,
I am using ppk2 to measure current on a custom board based on particle bsom (nrf52840). I am running ampere meter mode and I can measure some current, but values looks...
Hello Nordic Community,
I installed the serial LTE modem application on my Thingy:91 so that I may use it as a standalone modem. Using minicom on my Linux machine, whenever...
Hi,
I’m quite new to the nRF5 SoC’s and currently facing a problem with USB virtual com port communication using nRF52840 dongle (PCA10059) . I need to get results from...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
I want to get the VBUS input detection status (USB detected or removed).
I have confirmed that the current state can be known by reading the value of the register...
I needed to rework the memory map, to change the size of the slots to accommodate for a larger foot print. In the programmer, is an "Erase & write" with the hex file sufficient...
Currently the CAF Bluetooth LE advertising module only uses static advertisement data in ble_adv_def.h
Would it be possible to add an interface for setting manufacturer...
Hi support,
We have a product that successfully utilizes DFU and is currently in production. However, we have been seeing a couple units that failed DFU but can still...
Hello all,
I'm trying to send SPI signal from nRF52-DK to other circuit component.
nRF52 doesn't receive data, and send 16 bit data at one transfer.
I want to send data...
Developing on nrf9160 using NCS 2.1.2 and MFW 1.3.3, is there any sort of Hard Fault detection and handler besides the k_sys_fatal_error_handler hook in lib/fatal_error/fatal_error...
Hello,
I recently ordered a Thingy:53.
The first time I turned it on, I successfully tried the Edge Impulse app, and updated the Thingy:53 network and app firmware via...
Hi, my slave will send 55 bytes to SPIM, if I check slave data when SPIM received all data, and it will spend 1.8ms, I think its long.
Can I check data when SPIM starts...
Dear Nordic team, We are using the nRF connect SDK version 2.1.2. Our prototype uses the nrf52840dk board and the KScan application template. However, when directly trying...
