Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am using the nRF52833 DK and a Nordic-designed antenna array (12 antennas with 0.02m spacing) for an AoA Direction Finding project. I obtained the IQ data using Direction...
SW version :2.4.0 HW revision: nRF52833 development board, PCA20054 Direction Finding Antenna Board 1_0_0 I use the routine director_finding_central and director_finding_periopheral...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you.
I just want to explore on nRF52840 BLE section. I was not able to detect the device...
Hello! I have 126 kB MCUboot partition which I'd like to make immutable (write protected so it can't be corrupted). I have serial-recovery, KMU key handling, debug optimization...
When building applications/hpf/gpio with -DSB_CONFIG_HPF_GPIO_BACKEND_ICMSG=y on nRF54L15 DK (NCS v3.2.4), the build fails with error: '__device_dts_ord_DT_N_NODELABEL_ipc0_ORD...
Dear DevZone Team
To detect possible TWI slave devices connected on a TWI bus, we want to scan for device addresses and check if they are being acknowledged.
In the twi_scanner...
When a BTLE Connection is underway, calling bt_disable can result in an infinite hang in the Zephyr BTLE stack. Using ncs v3.0.0 Any ideas? There is some mention of: CONFIG_BT_HCI_ACL_FLOW_CONTROL...
I have implemented the erase protect and app protect in our application. There are commands for locking and unlocking the device. Actually, during testing I was able to lock...
Hello Team,
I am working with Thingy: 91x and I have searched your websites for Schematic for some understanding purpose used in Thingy: 91x Kit.
But I couldnt find any...
Hello, I started working with the nRF Cloud and have been trying to understand the authentication procedure. From my understanding, the create_credentials script creates the...
Greetings, my name is Toni. We are trying sending the MO PS SMS-over-CP/NAS or IMS from the nRF9160-DK: - Hw rev2, - mfw v1.3.7, - NCS prebuilt apps from the v2.3.0 and v3...
Hi Nordic team,
I am designing a new board from scratch around the nRF52832 in KiCad.
My current plan is to use the nRF52832-QFAA/QFAB QFN48 package on a 2-layer PCB....
Hi,
Using the Matter template sample, I'm not able do to the commisionning until the end because I got an error saying " an error occured" on my border router( using an...
We are currently developing a nrf52840 firmware which should support RSCP as collector.
Setup:
nrf52840
ncs2.9 with
Q322804 NCS Host
Q331587 SoftDevice Controller...
Hello,
I have been trying to find an answer to this in the documentation but have thusfar been unsuccesful. For our use case we use the Certificate management part of the...
