Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello Sirs,
I loop typing the same command program:
clear>tart_channel 02>output_power pos0dBm>start_tx_modulated_carrier>cancel
After repeating the same instruction...
Hi,
Project development using board with HL7800 modem similar to Pinnacle 100 did not succeed with FOTA upgrade so it is been decided first to try it with nrf9160dk_nrf9160...
Our product consists of a Texas MSP430 and a Nordic nRF52832 Chip, with serial/UART between
for MSP programming, debug and development : I'm using the official TI MSP-FET...
I am testing programming secure bootloader. But J-Link Commander reports Could not start CPU core. (ErrorCode: -1) after programming softdevice, bootloader, and application...
Hi,
Now I'm going to use 52833 USB_CDC_ACM , but there is no suitable type in SDK17.1.0. It's just have pca10056 . So I port to 52833 based on the 52840_pca10056 routines...
Hi team,
I am using nRF52833 DK with PCA10100 on it.
I am developing app_timer application for blinking led for a fixed time interval. But it is not working properly....
Hello,
We are trying to adapt the simple_gw example to receive temperature measurements from a zigbee temperature sensor. However we do not succeed. We can find the device...
I'm using an nRF5340 DK board with ncs v2.0.0. I have to build an application that should access BLE running in the network core. I see there are two options provided, Remote...
Dear Nordic engineers
I have a probelm would like to ask you.
I read this link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Ferrata_nRF21540_Rev2%2FERR%2FnRF21540...
Hello，
I am developing an AoA Tx project using NCS v1.9.0 & 52820. Some problems are hard to solve by myself.
Below is my configuration:
1.When CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC_CALIBRATION...
Hello,
we are using the "AT%CCLK?" at it works very nice.
but now for the challange... since the modem is synchronized with the LTE network and sends on the designated...
I notice a problem with the MCUboot Hello World example.
I followed the steps mentioned in https://www.mcuboot.com/documentation/readme-zephyr/ That is, build the MCUBoot...
