I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I need to implement a mouse and keyboard (combo) HOG device. There are mouse and keyboard samples, but may I integrate them in just one?
Is there any samplecode?
I have...
To whom it may concern:
We have a product in production based on the nrf52810 and SD 112 ver 6.1.1, developed with SDK 15.3. Due to our manufacturer having nRF52810 availability...
Hello,
I've been trying to access the nRF52840 dongle through the pc-ble-driver-py library. However, I can't get the Nordic examples to run. Here's what I did so far:...
I want to send my sensor data from one node to another node using BLE mesh. my data is at about 128 bytes I am trying to create a custom model but it's hard to know how to...
Hello, I am trying to advertise twice in my project with different gap_params.
First, I have started advertising with the following conn_params (shown below)
#define MIN_CONN_INTERVAL_ADV...
In a old post https://devzone.nordicsemi.com/f/nordic-q-a/58034/uart-communication-between-nrf52840-and-nrf9160-on-nrf9160-dk This question was already answered but this solution...
I am now using nrf52840 dongle and want to develop a software to control dongle like NRF connect desktop software, such as scan devices, connect device with passkey, read...
Hi
I am interesting to generate 1,638,400 Hz is an external clock for a peripheral on one of the NRF pins.
Please advise how can I generate this clock value on one of...
To the kind attention of Nordic support team,
We have this custom board using nRF52833 powered up from usb and in high voltage mode (ldo). The problem is that we are...
VS Code (running on Ubuntu 21.10) can't find the connected nRF52840 dev kit. " Could not find any connected boards " is all that's shown under CONNECTED DEVICES. Beside that...
I'm learning to use the Asset Tracker V2 example and planning to build a POC product on top the example. The biggest issue at the moment is with power consumption. On the...
To the kind attention of Nordic support team,
We have a problem that may very well be linked to this thread
https://devzone.nordicsemi.com/f/nordic-q-a/65202/usbregstatus...
Hi, I got my border router working fine, but I do not understand its use. How can I connect (which kind of protocol?) with the nrf5340 from my laptop to send turn on a led...
Hello
We check the current in system off in PCA10059 board. and use the ble_app_template application.
If set the VDD 3.3V, after the system off, measure the current is...
