Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi,
I am trying to receive packets from a device with Zigbee custom profile. Through sniffer, I can see that the device joins the network and sends packets on it but I cannot...
Our board doesn't have LFXO, but I want to run DTM. When I try to switch to LFRC by changing sdk_config.h, it doesn't take effect.
chip: nRF52832
SDK: nRF5_SDK_17.0.2...
Hi, we use the Fanstel BT40 design a RS232 & USB carrier board, when we use battery 3.3V to VDD, there is a DC2.8V output from VDDH. VDDH should be power input, why there...
As known in SDK nrf there is a function battery_level_in_percent() used to calculate battery percentage but it is only true for the CR2032 battery. Currently, I am using AAA...
My application uses a SPI LED driver, which I routed on a PCB to the most convenient pins for routing.
I have already tested my firmware on a nRF52833 DK with an Arduino...
Hello, I'm a beginner at developping nrF52832. My problem is completely similar to this one : devzone.nordicsemi.com/.../add-saadc-peripheral-and-others-to-example-project...
I am trying to measure single-phase mains voltage (240v, 50Hz) by stepping down the voltage to 200mv using a voltage divider and read it with the ADC pin of the controller...
Using NB- IOT JIO SIM in india, not connecting asset tracker Work Up to RRC Connected and stuck there. This is custom code very similar to asset tracker example. We are using...
Dear Sir.
Using the mqtt_simple project , I inserted a 1 sec timer.
Within the timer I want to use the publish routine like this
data_publish(&client,MQTT_QOS_1_AT_LEAST_ONCE...
Hello everyone, we are developing a heart hare accessory for the phone and we want to show the battery status directly on the phone. I found it can show up in the Windows...
Hi, I run nRF5 SDK 15.3.0 with SES 4.30c on a PCA10040. Yesterday I upgraded to nRF5 SDK 17.0.2 and SES 5.60. When I connected PCA10040 I got a message that something wanted...
Hi everyone,
I write a firmware to read the values from a 6-axis IMU and some force sensors. I want to sample with a frequency of 100-200Hz, to store the data in a buffer...
Hello,
I have already a Thingy:91 running and sending me data over MQTT using the mqtt_simple Sample.
Now I wantet do change the broker to one with credentials but unfortunately...
