Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I would like for the high duty cycle direct advertising to restart immediately after the ~1.2s timeout.
[I'm using Zephyr. I'm also really new to programming these devices...
Hello, i´m having some problems with the SIM card on my custom NRF9160 board.
if i try to use the AT%XSIM? command to check for the UUIC state i get the following response...
Hi Nordic Community
I was using the nRF Connect Android App to scan the contents of the advertisements sent by my board.
My device is C7:51:E9:6E:C7:43
My question...
When using the mcumgr tool to list images on the NRF5340 development kit, the bootable field is reported as false , and the flags field is empty for the flashed image. This...
Hello Team, I'm trying to use the implement some WolfSSL extensions into my project and get errors while building it.
Preinformation:
I installed the SDK v2.7.0 using...
On our platform we have the following configuration of firmware:
Master boot record
Boot loader
Thread application (compiled separately from the boot loader)
We...
Hi,
I am trying to write a file with dummy data on my internal flash memory mx25r6435f of nrf5340. Then read back from the file and see it in putty. Here is the folder...
Hi
I have an external NOR flash chip which is powered off on startup. The idea is to power up the flash when needed to reserve power. On startup, I get the error message...
I haven't found much documentation yet regarding multiple threads in the secure partition, so I wanted to ask if this would be possible. Was planning to also test it out myself...
Hi,
We have a requirement to not exceed 63 mW of WiFi Tx power at any time for any band (2.4 or 5 GHz) . There is a statement about changing Tx power is not supported. Can...
Hi, We are currently migrating our project, originally developed with NCS version 1.8.0, to the latest NCS 2.7.0, while incorporating MCUboot for both of them. During this...
Hello,
I am encountering an issue with the nrfutil settings generate command. Each time the command is executed with the exact same parameters, the resulting settings.hex...
SoC: nrf52840
SDK: OpenConnect 2.4.4
I have been developing an ambient noise system using I2C microphone, nrf52840 and Zigbee networks for some time. The firmare reads...
Hi,
Is nRF52811 / S140 capable of simultaneously being in peripheral (connected slave) and central (connected master) mode like described in this blog post https://jimmywongiot...
I’m working with the nRF5340 and nNF Connect SDK 2.6.1. I’m encountering an issue where, after a central device (e.g. an Android phone) forgets a bonded peripheral device...
