Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
I'm planning to replace some parts of my circuit with nPM1300. Heres my existing circuit. USB micro -->> lithium ion charging chip---->> Battery--->> Mosfet switch with push...
Hello
I have a project, where I need to have NUS-BLE with firmware update functionality and openthread.
BLE and NUS config:
FOTA config is:
Thread config is: ...
I'm struggling with SDKConnect and the device tree stuff... and finding it hard to get good examples or docs TBH
So, I have the sample dts files for the nRF5340DK, which...
Hello, I have a problem with the bluetooth connection to a Samsung s21. It connects for like two seconds and then disconnects immediately. Then tries to establish a new connection...
In build configuration i need to select nordic board . i have been using fanstel bt840 use nRF52840 QIAA, ARM Cortex M4F, 64 MHz . what board i have to select in this ? or...
Hi I am trying to interface QSPI with NRF5340 dk board. I am getting build errors. I have used SPI-FLASH sample and it was working fine and I am trying to change the SPI-FLASH...
Hi,
in the new version of nrfx there is a function (nrfx _uarte _rx _new _data _check ( &uarte _instance ) , and how to get a similar result for the older version of nrfx...
We are working on a project, with a working secure buttonless bootloader that works flawlessly. However I recently made it with bonds, and it works with all of the devices...
I'm experimenting with the Bluetooth Throughput sample in NCS v2.6.1. As I increase the distances between devices, I see strange gaps in the transmission from the Central...
Hi,
We are working on integrating nRF-Mesh-Library (iOS and Android) sdk into our app for mesh networking, it should support identifynode, provision, add app key and add...
I found a similar thread, but it did not solve the problem. When CDC-ACM is enabled in Device Tree, the dfu-util application cannot find the USB port. The Bootloader started...
Hi everyone
I am using nrf52840 costume board. and using NUS ( Nordic Uart Service ) as the basic start sample.
My desire:
1. UART0 and UART1 work in async mode with...
If I enter the prj.conf settings according to the lesson text then the firmware crashes with different provisioning functions from the smartphone app such as forgetting a...
It's looking more and more like a lot of my problems relate to a weak cell signal. Is the RF front end on the devkit known to be inferior to a normal cellphone? My personal...
Hello, I have connected a LR1110 module to a nrf52 (PCA10040) development kit using Arduino connectors. Anybody written a simple application regarding the interfaces?
It...
