Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I'm looking at the ZBOSS for Zigbee IAS Zone example , and in the " ZB_ZCL_DECLARE ..." statements it refers to structures such as zone_attr , poll_control_attr , and pwr_cfg_attr...
For nrf52x, a pin can be dedicated for reset, and this is from my understanding how HCI works in the sample (host line to controller reset pin). However, for the nrf5340,...
I am doing ble beacon device communication. I have two device, receiver and transmitter. Receiver device height is about 2 meter. Transmitter device on the ground. The distance...
My project builds fine in versions previous to 2.0.0. However, in 2.0.0 I'm getting an undefined reference. Any ideas where to look to track this one down?
/opt/nordic/ncs...
I am in the early stages of development and would like to proceed with only non-secure partitions on the nrf9160. I'd like to not make use of TrustZone.
I notice all of...
Hi Nordic,
I want to use an Arduino USB host shield with NRF52840-DK. Since the VDD on DK is 2.5v and MAX3421 on the shield works with 3 to 3.6 volts, I have to use an external...
What is the state of the GPIO pins during programming.
Because of space restraints, in order to get the the programming signals out from under the laird module we are...
Hello,
I am using a nrf52840-dk and communicate via SPI with an external board (NUCLEO-L476RG from ST) during development. For the development itself I am using the nRF...
Hi,
When starting to learn nRF currently, is it better to start with nRF5 SDK or nRF Connect SDK? I know Nordic will not add new features to nRF5 SDK, but what if I want...
nrfjprog restarts nrf5340DK debugger
We are running a container environment in Ubuntu 20.04 on WSL2 and the USB ports are frwarded using usbipd
When trying to flash (or...
Hi All!)
I am using nrf52833/20 Dk and am able to connect the two devices using coded PHY connectable mode by the available examples ( BLE_App_Uart and BLE_App_Uart_C )...
Hi every body.
I have trying without success to attach an event handler function to the TWI.
I am reading a temperature and humidity sensor using I2C. In polling mode...
Dear Nordic Engineers
I would like to add usb bootloader to ble bootloader.
I modify config of pca10056_usb_debug/sdk_config.h and add .c .h file of pca10056_usb_debug...
Hi DevZone,
What I am working with:
I am working on a project using nRF Connect SDK with VS Code, and I am also using the nRF Connect extension for it.
My issue...
