I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello everyone
I have a bunch of custom dongles from the company I work for and two of them started to behave in a strange way after I tried to erase and program them through...
Hi,
I'm currently in the evaluation phase of a project and would like to use a NRF52 chip, but I need to ensure, that I can use two independet hardware timers. I had already...
I am running a PWM pin on 15 using this DT Overlay:
pwmnmos {
compatible = "pwm-leds" ;
status = "okay" ;
pwm_nmos0: pwm_nmos_0 {
pwms = <& pwm2 15 >;
};
...
Hello,
I built my application based on your "ble_peripheral_lbs_coex" example. Board is nRF5340DK.
Mesh and BLE (NUS service) run together but I noticed that the NUS UUID...
I'm using SDK 17.1.0, softdevice 7.2.0 as a Bluetooth peripheral. I'm sending notifications to a paired iPhone. The notifications are keyboard keys, and so are time sensitive...
Hello,
I am trying to figure out how to save a small number of counters to local non-volatile memory on the nRF9160. I have a few questions.
1) How do I determine whether...
Hi
I want to measure chip temperature of nrf52840.
For this I referred " sdk-zephyr / samples / bluetooth / peripheral_ht / src /hts.c"
and I have enabled "CONFIG_TEMP_NRF5...
We are using nRF9160 DK (SDK 1.9.1) with "serial lte modem" firmware. We are trying to test downloading files from a server using AT commands to work with HTTP. The file is...
Upto a week I had *no* problem in programming a nRF52840 dongle with an app I am porting from the nRF52840dk.
All of a sudden I can't get the app running, the dongle appears...
I'm trying to get sprintf working with SDK 17.1. Basically, I'm struggling getting this simply use-case to work. char buf[32]; sprintf(buf, "%.3f", 3,5); I'm not able to find...
I know from zephyr samples that Tensorflow lite is available via zephyr as an external module, though it's not explicitly allowed in the nrf west.yml, and therefore is not...
Hi all, I follow example (serial) to build and run, i already run successfully, but i meet some question. when i use generic_on_off to control light at short time(2s), the...
Hi,
On a NRF52840, I try to perform `x` SPI transactions of 3 bytes each using EasyDMA Arraylist feature fully controlled by hardware. The CS must be toggled between each...
Dear Nordic Experts, The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832. When provisioning, it sometimes...
Hello, All
I am trying the scan_adv example, and use my phone to scan the advertising packet, unlike other peripheral examples, I found that it appears multiple time with...
