Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
I need a checksum to verify integrity of some data blocsk. As I saw, that the nrf5340 hardware has some builtin support for SHA-256, I though: cool, let's use SHA-256
Now...
Hi,
I build a custom board (nRF52840) but I'm not able to flash it using nRF5340DK with J-Flash via SWD interface.
1. The first thing I did was to do a full chip erase...
Hi,
Is it possible to communicate with the nrf52840 dongle from an android application via USB port ?
That is, nrf52840 dongle will be inserted to the android phone's...
Take Bluetooth UART as an example, there will be a delay in the process of sending data from the peripheral device to the central device to receive the data.
What factors...
Hi, I'm developing for a custom project board which only has the SWD pins exposed, which I'm using for (1) programming and (2) RTT logging during development.
Once the device...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and would appreciate some insight into how Zephyr...
Hi, I use NCS v2.6.1 I have taken Central and peripheral HR as an example and am trying to modify it to make the Central/Peripheral UART example work similarly.
I briefly...
Hello,
I'd like to add the transmission of an I2C recovery pulse (where you toggle SCK 10 times) to my startup routine for an offboard device whose state I'm uncertain of...
Hello Nordic team,
I was wondering if it's possible to start the MCU boot from the application at runtime.
What I want is to be able to restart my product and run...
Exercise 2 doesn't seem to work for SDK v2.6.1 with v2.6.1 toolchain. SDK v2.5.1 works though. What configuration or code changes do I need to make it work for v2.6.1?
Hello,
I was curious if there was a project that uses 2 Mbps BLE to connect two nrf52840s, preferably with the ability to change which BLE channels the devices use. I...
hi professor,
The npm1300 is used for power management on my borad.When VBAT and VBUS are connected simultaneously, the bulk 2 output power supply varies between 1V and...
In our custom board, check flash write and read using sample (C:\ncs\v2.6.1\zephyr\samples\subsys\nvs) but showing following response. the same build working fine in nrf7002...
This issue is for a programming environment on a macBookPro.
I finally get the system tamed and got to the point of testing the various sample apps provided. I wasted a...
Hello,
I have trouble again with TX Power control. This time using Softdevice Controller and NCS2.6.0.
Previous issue which was solved (this was using Zephyr Controller...