I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello,
I have the nRF54L15 PDK and am experimenting with the intermediate tutorials for the Zephyr RTOS. I am working on Lesson 1 - Exercise 1 ( https://academy.nordicsemi...
nRF Connect 5.0 crashes after asking to install nrf-device-lib-driver-installer.exe and shows the following cryptic message.
Trying with nrfconnect-setup-4.4.1-x64 raises...
Hi,
We have a nRF5340-DK board with the following setup:
b0 as the first stage immutable bootloader
MCUBoot as the second stage upgradable bootloader, which needs...
Hello, I have an issue with a project I'm working on with a nRF5340 Audio dev kit. I am using VSCode with the nRF Connect SDK plugin, and SDK version 2.6.1.
I need to have...
Hi,
We are working on nRF5340 with TF-M enabled and iOS application.
What we are observing is the peripheral device MTU TX and RX are configured to 512 bytes whereas the...
Hi I'm using nRF7002-DK kit and I noticed that the output voltage of a GPIO is 1.8 V instead of a 3.3 V. I have encountered a solution mentioned that we should apply these...
I’m working on an nRF52832-based project using the Nordic SDK (v3.5.99-ncs1-1) and MCUboot for OTA updates. I have a 512KB internal flash and 4MB external SPI flash (P25Q32H...
we are using SPI3 in nrf52840 with nrf SDK 16.0
we are using this as below
1. SPI3 init -polling mode
2. SPI3 unint
3. SPI3 init - DMA mode
4. SPI3 unint
5. SPI3...
Greetings,
Is the command toggle_dcdc_state supported in the radio_test sample when compiled for the nRF5340? ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
I started with the BLE provisioning sample (ncs\v2.7.0\nrf\samples\wifi\provisioning\ble) using nrf7002dk/nrf5340/cpuapp build target with sysbuild which works fine to provision...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
I am trying to use the `ram_report` tool and the results seem to have some issues:
1. The total size reported is much more that that reported when linking the zephyr.elf...
We are not using system off mode. since we not using external rtc. We are using internal Real Time counter in system on idle sleep (using ksleep).
In Basic led code , We...
We are building a Bluetooth remote using nRF52810 and nRF connect SDK v2.5.1
The remote have 20 buttons to be transmitted every 100mS, and we need several LED on / off commands...
I am trying to measure the battery voltage on my custom board which is based on the nRF52832 device. I am using nRF Connect SDK 2.7.0 in VS Code. The dts file for this custom...
