Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hello,
I am planning to use the nRF5340 in High Voltage mode and LDO mode. Currently, I am designing a PCB where minimizing the component count is critical.
I understand...
HI
I previously used the NFC feature in SDK version 3.0.0, which had an abnormal current issue after each trigger. After applying a patch from the forum, this problem was...
I’m designing a PCB using NRF9151-LACA-R7 and an NRF52810-QFAA-QFN48 Our CM needs the exact temperature data for SMT reflow , but we can’t find it clearly in the datasheets...
Hello, I am currently working on development on the nRF54H20DK and the nRF7001 shield. I am yet to find documentation on if these two are capable of sharing a singular antenna...
Hi,
We're trying to preprogram our nRF54L05 SoCs before SMT as this is more efficient in our production process. In the past, we did this successfully with an nRF52810,...
When trying to debug my non-secure app, I can hit the break point once, but after that, any stepping or continuing results in tfm_hal_system_halt via MPC_Handler(). I'm using...
We are running some internal training on cellular, and it seems that Lesson 4, Exercise 2 is missing something (in the tab for NCS v3.2.0); the instructions to provide the...
I am currently working on a project involving the Nordic nRF52840-DK development boards (1 Central and 11 Peripherals communication), with LE PHY Coded S8. In this project...
Hi,
I’m using an nRF52840 SoC and currently developing with NCS 1.8.0 . I need clarification on the Bluetooth Core Specification version support :
What Bluetooth version...
Hi Nordic，
I am using the nrf52840 as the host and the nRF9160 as the modem with the serial_lte_modem library.
Normally, when the nrf52840 sends an MQTT connection request...
Hello,
I am planning to design a custom board using the nRF5340.
My main question is: How can I view log messages from source code running on the custom board on my...
hello,
I have a neo pixel running on my nrf52840 using SPI. I still require the SPI clock pin to be configured to a pin even though it is unused. This wastes a pin, is there...
I took the example of peripheral_hr_coded and central_hr_coded. I flashed these examples in nrf52840. They communicate normally. However, the Advertising Packages are not...
Hello,
I'm using the zboss stack to implement a zigbee end device on nrf5340.
My device is able to connect to a zigbee network and to notify sensor events on zigbee but...
Hello, I am using the LIS2DH sample (and the st,lis2dh driver, which is compatible with the LIS3DH accelerometer) to test out a LIS3DH IC attached to a custom board. However...
