[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hello,
I would like to ask you if SoftDevice S132 v.7.x.x allows Master-initiated Feature Exchange procedure?
BLE Core spec: Vol6, Part B, Cap. 5.1.4.1.
I tried to find...
Hi everyone, I use nrf52833 to make dongle. My test found that after suspend of usb, I tried to enable ESB rx mode, but I couldn't receive rf data. What is the problem?The...
Hello,
When deleting a bond from the central, after trying to reconnect with the peripheral the PM_EVT_CONN_SEC_CONFIG_REQ gets called as expected. I know that allow repairing...
I have been trying to develop a project, my custom board has a nRF52840 chip and I have a nRF52840 DK too.
My problem is when I try to debug any example from any SDK....
Hi, I attended the Nordic Seminar in Tel Aviv last week and heard several lectures from your experts.
It was recommended that we use a module with Nordic IC rather than...
Hi,
I am using vscode and nCS on windows, kindly help me with below 3 queries:
1. How to generate a binary signing key, say "KEY_1"..?
2. How to sign a binary with...
Hi,
We are trying to use PPK2 to measure current of our board, we want to receive the data from PPK2 and parse by our owner python script, so could you provide the protocol...
Reading The adhoc smart waste solution uses the nRF9160 SiP I tried to reproduce the mention 6 µA with LTE-M in eDRX with an interval of 655 s.
I use
CONFIG_LTE_EDRX_REQ_VALUE_LTE_M...
Hi,
We use PPK2 very conveniently as a logger for testing.
How about adding the supply voltage as display options also?
We hope you will consider this.
Thank you...
Hi dear,
It is possible to establish parallels multi connection to different J-LINK's devices serial numbers via nrfjprog.dll, or any other automated way ?
We successfully...
Hello, I'm making a breakout board with nrf52832 qfaa. I used chip antenna (2450AT18B100E) and followed Nordic reference layout. I am getting around 60m range in an open environment...
run nrf Connect for bluetooth Low Energy Standalone
connect PCA10040 board
select "server setup"
press "+ New service" which adds a New Service
press "> New Service...
Hi, I am currently learning to retrieve location using thingy 91 and location example from nrf SDK. When I run it, I got this message (below).
After doing some research...
I want to change the data in the registers of Radio peripheral when the Radio at the state of "Disabled",but with no respons.
Only if I repower the Radio it works,but why...
