Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Following Setup:
1.) Building light-switch-app from original https://github.com/project-chip/connectedhomeip Repo for nRF5340 from command line with nRF SDK v2.1.0
2...
Hi,
We are close to going into a certification process but before we start we need to be sure we are not missing out on your recommendations with regards to EMC performance...
Hi,
I get the error like below on the Linux XFCE 64-bit platform (Pardus 21.2 distro latest version). It works fine on Windows but having a problem on linux. How can I solve...
Dears,
Currently, when working with the nRF52833dk, I found some weird behavior.
I tried to run the blink example in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_blinky...
Hello. I want to check "Airlog" or "hcisnoop" with nRF5340 LE audio EVK. The current development environment is VS Code. I also have a USB Dongle, but I don't think I can...
Hi,
I'm using nrf52840 with softdevice s140_nrf52_7.2.0 and I'm adding new characteristics to the ble_nus service. I've added the new handles for the new characteristics...
It appears that after a few seconds and sometimes after a few minutes sleeping threads do not wake up, even though the UART shell and BT NUS are working. The only service...
Hi,
I am trying to configure GPIOs with a custom DTS file, for initial bring-up and testing of the PCBA prior to higher-level development. During compile, I am getting a...
Hi, we have a use case where the central might need to re-bond with our peripheral (e.g., after choosing "Forget this device" in phone settings). I have learned that setting...
Hi
i am working on the nrf5340_dk for making as a controller through the hci_uart build.
can i know the gpio connection mapping on the board?
regards,
Achyuth
Hi, I'm currently having a problem with the uart peripheral.
I have an STM32 MCU connected to the NRF52840. In this case, the NRF acts only as a "transceiver".
Whenever...
I have my own code for handling pin interrupts using the NRF_GPIOTE EVENTS_PORT interrupt. I had some issues with this years ago when I was using the nRF52832 chip, which...
Hi,
is it possible to configure the hci_uart example from NCS in a way that the FICR device address of a nRF52840 is used as public device address? I cloned and compiled...
Hello,
We are trying to get the NVS example on our nrf9160 DK running. The build and the flash process looks fine but the application won't boot. Not even the typical...
Hi,
I bought a second nrf52833-dk. After I program my code on it, I can't debug or read the code because read protection is on. This is strange, because I didn't program...
