Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
In order to use "psa_" crypto functions I use "CONFIG_NRF_SECUIRTY=y". I am also using mbedtls for TLS1.2 networking via external WiFi module
By using NRF Security, the...
Hi Team,
I'm installing nRF connect SDK in my PC and i'm using ubuntu for Zephyr RTOS.
When i'm run this command that time error is coming "west init - m https : // github...
I need to use can bus for my application. The chip that will be used will be the MCP2515 can bus ic. For testing puposes i went and tried the CAN sample which is meant for...
I had look on overlay-low-power-conf file and in folder child_image on spm.conf file that UART_SERIAL=n is set. I need to interface a UART device to nRF9160.
1. Is asset_tracker_v2...
I installed the nRF Toolbox on my phone and received data through BLE uart. However, how can I download/save this data on my phone? For example, I send the temperature to...
Hi,
I'm trying to send an data array over ble nus.
This didn't work.
I'm also getting this warning.
I'm doing something wrong, but I don't know what. Do I also...
Hello,
I am making a Firmware for the FCC certification, I must emit at 3 different frequency, 2404MHz (ch37), 2440MHz (ch17) and 2480MHz (ch39) on a nrf52832.
I unfortunately...
Hello,
I have installed the NCS toolchain using the Toolchain Manager app. I am using toolchain version 2.0.0. Here is the error I get when running `west status` :
Same...
I received Thingy:53 and tested it by following the Getting started with Thingy:53 SDK documentation.
The problem arises from the sentence below.
Getting started with...
Hello,
I'm using the LTE Link Monitor v2.0.1 with the nrf9160dk_serial_lte_modem_2022-06-02_880c82db application on a nRF9160.
I'm able to establish the connexion and...
I saw a news report on Nordic's official website that Nordic's NB products have passed the certification of Chinatelecom. I wonder if they have passed the certification of...
Is there a way to add an offset to the nRF5340's reported RSSI to compensate for any front end loss or gain the design might have? This is to get to an RSSI value at the antenna...
Hi,
I'm using HID mouse example in SDK17.02.
After downloaded soft device and the application, I add the device in my pc blue tooth. I can see the battery level normally...
Hi,
I'm looking for a product Bluetooth 5.2 Radio System-on-Chip (SoC) which is of automotive type, and their operating temperature ranges are (-40 to +125)
I'm working on Electronic Shelf Label project using Feather nRF52 with Raspberry pi for server connection. I need to Adafruit Feather nRF52 to receive data from raspberry...
