Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
I have an Zephyr application on the nRF5340 that I've been working on. I can debug fine in SES without a boot loader. However, when I add MCUBoot into the mix then everything...
I have some code that runs on the application and network processors that uses NRF_RPC NRF_RPC_CBOR (similar to the entropy_nrf53 sample) to communicate during boot loading...
I'm trying to get setup to debug an application that uses both the app and net cores. For now I'm using the example nrf/samples/nrf_rpc/entropy_nrf53/cpunet. I'm trying: ...
I am migrating our mesh network stack to NRF 52840, which is based on 802.15.4.
I would like the code to be more efficient state machine so that I don't have to busy-wait...
Hi,
I am using the ble_blinky example as a template to develop my project, with nRF52832 and SDK 17.0.2.
My first goal is to reduce consumption, so I have changed the...
Hello,
i had a look at lwm2m_client_sample and it worked pretty well. Now my next step is to be able to send for example a 100 or 500 Bytes Payload from nRf9160 to Leshan...
Hi Karl,
Sorry, I inadvertently closed the issue.
In my understanding, with SW9 in position "VDD", VDD_nRF is about equal to VDD_HV, so the measurement should work. I...
Hi
Is there an example for BLE "Just Works" using the NRF Connect SDK for the peripheral device?
I am using a peripheral device without display and would like to allow...
Hi,
In our application we use a motor. In the case that the watchdog would trigger while the motor is running, we need to stop the motor. For this we need to set the PWM...
Hi, all,
At first, I have to say I am a newbie in programming for BLE. ^^"
I trying to development a cycling power meter, so I want to modify this CSCS example to...
Hello, Recently I tested and flashed the Zephyr program to the nrf52840DK, it works fine. While I flashed as usual last time, I saw the LED5 flashing and then the PC didn...
I would like to perform a OTA DFU in a nRF52840 DK using nrfutil. For that, I'm using the example that is in SDK/examples/dfu/secure_bootloader/pca10056_s140_ble in the target...
Hi
I have follows the following steps.
1) I build 'hci_uart' sample for nRF5340DK successfully by following guide https://docs.zephyrproject.org/latest/samples/bluetooth...
Hi, I tried the fourth step of this guide https://openthread.io/codelabs/openthread-hardware#3 , but if I start the OpenThread daemon, I got this output that is not the same...
