hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
why doesn't the mesh chat example work on nrf5340?
I know it's not included in the list of supported platforms, but I'm trying to figure out why.
I can compile and upload...
Hi,
I've noticed that when I'm not initialize BLE stack, I have a failure in nrf_sdh_soc_evts_poll function (NRF_ERROR_NOT_FOUND).
Can you please explain what is the reason...
Hello:
nrf_pwr_mngt_run() doesn't always work on my custom board. About 1 time in 3, in code (I'm running in debug mode and using RTT) spits out
ERROR 3735928559 [Unknown...
Hi. I flash a board with NRF51822 via SWD pads, and that way the push button is inaccessible, and I need to press it to test various functions. Push button is on 28 bit and...
Hello,
I am using the n RF Connect SDK v1.5.1 and using the Zigbee Projects.
I wanted to know if and how to change the default stack profile of the Zigbee App. The following...
Hi! I am trying to interface the CCS811 with the nRF91-DK. For this purpose I am using nrf-sdk 1.6.0 and "ccs811" sample from zephyr. I created a nrf9160dk_nrf9160ns.overlay...
Hello,
I developed a code for nRF52840 Dongle to publish data on mqtt-sn topics (I'm currently using Nordic SDK for Thread and Zigbee). I need to know what are the limitations...
I'm working from the https://github.com/Martinsbl/nrf5-mpu-examples/tree/sdk13/nrf52-mpu-easydma-using-gpiote-and-registers example and the DMA portion is working splendidly...
I am trying to build the nRF Connect SDK project "at_client" that is provided with the IDE. I also tried the asset_tracker project with a similiar result.
This is my first...
i use a thread to save fil like below ,and find can not save file in sd card ,sd card SPI test ok . before enter in loop. close fil and reset system can save fil in sd card...
The first bug : I believe that the target level argument for the definition of the transition callback should be of type int16_t instead of the unsigned version since it is...
I'm trying to add a sensor driver to my project based off of Zephyr's sensor driver for adxl372. I can't figure out how to get the Kconfig file in that sensor folder to show...
Hi Nordic team,
I'm struggling with an issue where my chip wakes immediately after calling sd_app_evt_wait() - specifically if I call app_timer_start() before the wait for...
Hello, We are looking for production automated current measurement using your product Power Profiler Kit II. Is it possible to interface product using serial/commandline/python...
I wonder if anyone else has seen this issue. There are a few posts that seem to point to using nrfjprog to restore the board, albeit for nRF52. But nothing I have tried allows...
